Recent content by dingus

Thanks , They are for sale on ebay now that's where I bought mine. im not sure if theres anymore listed there now tho.

I did a lot more work on my 1995 4x4 E 350 7.3 PSD Van. I built a rear road armor bumper to match the front one all custom made, and made a motorcycle rack as well as a folding bed in the back. will try and post a link to some pics . Heres a link below showing my decals I installed I think...

Heres a picture of the cut out roof (before I removed all the extra metal ), everything below the gutter has to go ! its the hardest part I think. I have all my frame pieces ready to pick up from the metal shop all cut out to the curve of the roof. I will start a new thred just about the pop...

thought I would bump this up. Im now building a custom Pop Top roof for my van so I can stand up. similar to a sportsmobile but lower sleeker profile. I bought the entire original metal roof outa a 1998 E 350 from the wreckers for $300 this is a compleat metal roof. I want the new roof to...

Theres a scoop being installed on the under side of the hood going under the vents forward that any water snow ext that enters the scoop holes will run forward and drain down the front of the rad. Air will still flow to the K&Ns and any water that runs under them will just drain out two drain...

No sensor in the T there is a tube you can put a hose to on the back side but my van runs without that I just have it pluged.

Ebay as well its 3.5 dia Pipe and the adapters it comes with fit right onto my original air intake hose I just cut it off threw away all the crappy air box and original air filter compartment. Just do a search on ebay for air filter Y pipes the kits will come up. the filters might be OK but im...

Well been awhile since I posted anything new on my 95 4x4 E 350 Van ! Just got the two air intakes cut and installed for my twin K&N set up for the 7.3 PSD. The Hood scoops fit perfect to the shape of the ford Hood there Mitsubishi Lancer Evolution X carbon fiber hood scoops . You can buy em on...

I just went thru a VSS nightmare turns out my Crown gear bolts had come loose busted one off and it fell in the diff bottom and bashed the VSS ring gear over 1/2 inch so the VSS couldn't read the toothed gear as it went around. I pulled the carrier today what a mess. I doubt this is the OP...

Yes there very helpful guys at Clydesdale 4x4 there gona send me new Clydesdale 4x4 decals once I get mine repainted to any colour I want im not sure I want decals on it tho it has a Clydesdale decal serial number in the drivers door pillar so I might just be happy with that. they always answer...

Yes that's the exact same as my Clydesdale TTB E 350 PSD conversion van underneath except mines lifted more than that ^ van there. but the brackets are the exact same! Funny my van had Maui 4x4 decals on the original doors (mine now has 2003 power doors) and my van was done by Clydesdale in...

Heres my work in progress calling her VANOSAURUS REX lol its a 1995 E 350 TTB 4X4 Ford extended Van with a Turbo 7.3 PSD Converted by Clydesdale in Canada ive put a ton of custom stuff into this van even has power amp research steps (that was a job to install) and custom road armor bumpers ...

Yes its 4 wheel ABS in that recent pictures posted mine is similar but older I have one of the early conversions . the bracket welded to the cross member at the front looks the same as mine my radius arms are not fancy like them red ones but there lowered. the Back TTB bracket is bolted to my...

I have the same ARB fridge 50 Qt im just putting it up front on the floor behind the drivers seat on slides cross ways in my 4x4 E 350 van so I can pull it right out and it will be closer to side doors also when slid out I can reach into it from my drivers seat to grab a pop then push it back...

Hey hi ! lotsa info in this thred on TTB van conversions eh.