Argento - The Overland Ranger Build

[B_Hayes]

Figured I would showcase my Ranger build here.

The basics:
2021 Ford Ranger XLT FX4

Here is the most recent state:

 

[B_Hayes]

I am a little outdated on quality images, but I will show a few of the potatoes I have.

Modifications:

1. Protection
   1. ARB Summit front bumper
   2. Coastal Offroad high clearance rear bumper
   3. White Knuckle Off Road sliders - welded on
   4. ARB skit plates
   5. Rough Country M220 differential skid plate
   6. Badlands 12000 lb winch
   7. ARB Recovery points
2. Comms
   1. Midland MXT275
   2. Icom IC-2730a
   3. Garmin inReach Mini 2
3. Lighting
   1. Auxbeam 7" round auxiliary lights
   2. Diode Dynamics SS3 yellow fog lights
   3. Diode Dynamics SS3 white ditch lights
   4. Cali Raised ditch light brackets
   5. LASfit 42" yellow light bar
   6. Auxbeam 22" lightbar on ARB bumper
   7. Garmin PowerSwitch
   8. Diode Dynamics SS2 running lights
4. Overlandy Accessories
   1. Prinsu roof rack
   2. RSi SmartCap - full bin on driver side, 1/2 bin on passengers side
   3. Decked drawer system
   4. ARB single air compressor mounted in Decked ammo can
   5. 67 Designs rail with Bullet Point Mounting Solutions 1 cm arms
   6. Jeep Uniq Icom mic mount
   7. Bullet Point GMRS mic mount
   8. Mil Spec Designs electrical tray
   9. Long Range America 37 gallon fuel tank
   10. Mishimoto/Bourne Offroad snorkel
   11. Snorkel Upgrade filter
   12. Raptor Grille
5. Lift/Performance
   1. OME HD front struts
   2. 1" strut spacers
   3. Icon UCAs
   4. OME SD rear shocks
   5. OME 2.2" medium duty lift springs
   6. Ford Performance Tune
   7. Faction Fab 1" wheel spacers
   8. 285/75r17 Toyo Open Country ATIII

 

[B_Hayes]

RSi SmartCap bins with the Decked system.



LASfit light bar mounted on the Prinsu rack. I have the wind deflector with the cutout on its way, I wasn't sure how it was going to mount until I got it.



Garmin PowerSwitch on the Mil Spec Designs plate.



This is the amount of wire I was able to remove from the truck by using the PowerSwitch.



Long Range tank ready to go it. And the tank next to the stock tank. 18 gallons to 37 gallons. Updated the truck in Forscan so capacity and DTE is accurate. I want from 250-300 gallons a tank to 700+.




SmartCap installed. You can see my tent removal/install mechanism.

 

[B_Hayes]

Some pictures in action.

 

[GetOutThere]

I'm a bit biased, but I love it. Gotta be getting heavy though, especially with the RSI.

Any idea where you are in proximity to GVWR?

 

[Roam.Wild]

RSi SmartCap bins with the Decked system.

View attachment 821089

LASfit light bar mounted on the Prinsu rack. I have the wind deflector with the cutout on its way, I wasn't sure how it was going to mount until I got it.



Garmin PowerSwitch on the Mil Spec Designs plate.



This is the amount of wire I was able to remove from the truck by using the PowerSwitch.



Long Range tank ready to go it. And the tank next to the stock tank. 18 gallons to 37 gallons. Updated the truck in Forscan so capacity and DTE is accurate. I want from 250-300 gallons a tank to 700+.




SmartCap installed. You can see my tent removal/install mechanism.

Looking awesome! But that Power Wagon in the back is extra awesome!

Probably the most complete Ranger build out there !

 

[B_Hayes]

I'm a bit biased, but I love it. Gotta be getting heavy though, especially with the RSI.

Any idea where you are in proximity to GVWR?

I don't know where I am right now, but I do plan to weigh the truck sometime soon. Just need to find a scale around here.

 

[B_Hayes]

Looking awesome! But that Power Wagon in the back is extra awesome!

Probably the most complete Ranger build out there !

That PW is pretty slick! I hear it needs 40s though. I appreciate the kind words!

 

[B_Hayes]

Swapped out the 7" Auxbeams for SS5s. These match my SS3 fogs, SS3 ditch lights, and SS2 running lights.




I also go the wind deflector with light cutout from Prinsu, and moved the light bar.