Search results

I found my blown fuse. It was getting dark the other day, so I didnt catch it but there were a pair of fuse with music sign under the hood for radio. I post pic here just in case anyone else need to know in future. Under hood fuse panel: Under dash fuse panel: Thanks guys :) cheers...

Oops. My bad ! 2001 Limited.

Oops. My bad ! 2001 Limited.

Hi all, hope your day is going well! I was working on radio wiring and accidentally shorted the power line and blew fuse somewhere. I lost power on both radio and the little display on center console. Anyone know where the fuse location is for this small display on center console ? I...

I use 285-75/16 and it fits fine with my stock suspension. It will be little slower but still daily drivable. Recently also met a guy with OME lift with 35” tire.

“Truck wanders all over” ... this sounds like you need new shocks. Does it happen when just one side goes over a bump or pothole ? I had my right rear shock go bad and whenever I hit bumps on highway, it was scary. Truck wants to fishtail. For other issues, everyone pointed you to some...

I did have similar shake on my steering wheel after balancing. I was already thinking my bushings were bad but went back to shop again to rebalance. Second time around, they got it right and it got smooth and no shake upto 90mph. I was happy! [emoji2] So start with rebalance and see where it...

Sorry to hear the frustration. Hope I can give you few pointers to help find the root cause. Can you check following ? - does vibration happen during braking ? Then most likely the rotor. - does vibration happen during acceleration or cruising ? If your ball joints, tire balance, brakes...

CALIBRATING SPEEDOMETER / ODOMETER with Yellowbox After changing Diff Gear and tires , I knew my speedometer had been off and odometer racking up inaccurate number of miles, I wanted to fix that. My speedometer was reading about 8% higher and I got annoyed specially on highway speed. Some of...

Thanks Inyoman! I think I will try to dedicate fund and time to do this setup :D.

It might be too late to comment but looks like you can just swap the hard line going into the pinion area? Then the line does not cross over like in the old one. It might be assembly error ?

Welcome! I think you are fine about Diff unless you cracked or dented it. I would use cross member. For me, I cannot lift high enough with my jack so I put piece of wood under crossmember. For stand, FSM shows to put it on pinch weld but I put it on body frame. Works ok for me.

Found this on FSM

I like your ride and pictures:) Hope you get to install awning soon For the heating issue, i would guess few causes -is your coolant system bled properly ? Could be some air pocket stuck around sensor ? -could be stuck thermostat? Did you replace it while doing timing belt? -faulty sensor ...

Thanks guys. Unfortunately mine is 2001 model and don’t have that traction control system. I have seen the “dancing pajero” video on youtube and its impressive. From what Michael explained, I understood as if I am using Hybrid LSD, it will perform well? Now, my stock diff had Hybrid LSD...

Regear: 4.3 >>> 4.9 Ever since swapping tires to 33”, monty became little sluggish and suffered a little on uphill. Finally got to time to swap out the diff this past weekend. So far I just replaced the rear one to try out and have been driving in 2wd mode. Stock setup was 4.3 : 1 ratio...

Hi Ilyas, I have same size but with General Grabber AT tires. Mine clears just fine most of the time. I had slight rub while backing up in the front passenger tire on fender liner (front of tire) but that was due to bumper bent in from previous owner. I pushed the bumper out to align correctly...

May be test the fuel pressure ? You could loan out the tester from parts store usually. Or start by doing regular maintenance / tune up. Cleaning your injectors, checking compression, etc might help you diagnose more. If unsure, I like tackling stuff by doing must do maintenances and see...

I moved to Westcoast from Midwest and glad not seeing rust welded parts anymore [emoji16][emoji16]

Thanks Jeep-N-Montero. Sorry if there was many discussio before already. May be I searched for wrong keywords. Your input makes me feel better about Lugcentric ones now. Pushing wheels out should clear rubbing issue on mine. rubbing mark was right on the plastic cover that shields the fuel pipe...