Search results

I am selling a set of one ton axles. The front is a Chevy SRW D60 out of a CUCV and the rear is a matching width D70. The D60 is out of a M1028 CUCV so it should have 4.56 gears. Most M1028's also came with a limited slip in the front which I believe this one has but have not opened to verify...

My 1996 T100. Nothing too fancy right now. 1.5in BJ lift front, 2in AAL rear. 255/75R17 BFG MT's on stock FJ Steelies, Home built rock sliders and winch mount/bumper. Smittybilt XRC 9.5 Gen2. ARE cap with entrance door on the rear. Plan is to outfit the rear with two sleeping platforms, dual...

The easiest way to tell what you can use is to make sure the vehicle its coming out of either has the 2.7 or the 3.4. this goes for either the pickup or the 4 Runner. Both of these have the driverside drop front diff you will need. As for the rear, I believe the 2.7 Tacoma with out E-Locker...

Appreciate the replies. As there hasn't been anyone to come forward with a futon/folding bed of some sort.. I am going to take that as a hint that it may not be the way to go. what does everyone use as bed pads? I saw where someone used the tri fold outdoor lounge chair cushion.

What type of bedding does everyone else use? I would like to leave the bedding in the truck but it isn't necessarily required. I have found one issue with the plan and that is the wheel well wouldn't allow the futon to sit back all the way. and then if you were to lift the lower portion up high...

So I am trying to decide which route I would like to go with my sleeping arrangement in the rear of my truck (T100 6.5ft bed). Plan is to build out the back into a small camping setup. Need to have enough room to sleep two people (my girlfriend and I). Along with some sort of sleeping platform...

Figured I would post mine up. Slow build, but most seem to be. I got the truck from my neighbor, a little old man that bought it new in 96. Had 262k miles on it and he said he had zero issues with it until the head gasket blew. Picked it up pretty cheap with the plan to rebuild it to exactly...

The email from Paypal with receipt number will suffice correct? or do they need the page directly from the paypal website printed?

daveyd, do you have a build on your setup in the back? any videos of the generator running? did you do anything to push fresh air to the genie? How quiet is it, can you say, run it at night (assuming you sleep in the back as well?).

I am trying to outfit a truck bed with camper top, diesel and propane heat just seem like more things to carry/expend on a trip. not to mention trying to figure out where to put a propane bottle securely while offroad. I also have a worry while camping about sufficient sunlight as I am on the...

So looking into heaters and what it would take to run them, as this would be the key thing I would want to run. It looks like solar is a horribly innefficient(read expensive) way of heating a space...

Ok first I would like to thank you for your help and appologize for the "Newb" questions. Here is what I am looking to do. I am trying to outfit my rig for weekend trips(3-day) and would like to have a setup in place that will last me that long but has the option to add on later. I, as well as...

Went to your page and read your plan for your trip. Couple questions, Are you planning on running the stock 1.3 if so, carb'd or efi? Any plans for a 1.6 or 1.9 switch? If keeping the 1.3 have you done anything to the engine like a rebuild or new gaskets or maybe a carb rebuild? If you are...

I assume you are just showing you put a hitch attachment on the bed with the ball hitch.. or are you planning to leave it there? Making a little gooseneck to go along with it? :smiley_drive:

First of all just remember when thinking about comparing diesel to gas, even though the diesel doesnt have the HP it has loads more torque, which is what were after in the offroad world. you also have to remember that the powerband and RPM range of a diesel is much different then a gaser. as...

What was the final cost after steel, hardware etc. What are the specs of the steel harware you used. have you tested the amount of weight you can place on it until it starts to show weakness? with the square style of how its made it looks like there could be room to put jerry cans, water cans...

New to the site, glad to see people are actually adventuring with their zuks. Im an East cost wheeler. In the middle of a build currently. Below are two pics, the first from what it looked like when i got the lil sami, the second what it looked like before the tear down. Currently upgrading to a...