Search results

Here are some pics of the actual awning, roughly 6.5 feet extended out

I have a 7foot long arb awning, barely used/opened. It has scratches on the case due to offroad use, also have the tie downs and stakes. $200 obo Would rather not ship, I'm located in Indianapolis IN

Bump, price drop to $500

Got the engine hoop figured out, I ran the tube with as minimal of movement of the items in the engine bay. It is un equal in angle, however it does give me room for my psc reservoir. (Ignore the too short tube, more arrives this week) I also added a third "leg" to the hoops. As well as...

Trackbar is tacked together, as is the tie rod. I had to put roughly a 10 degree bend in the trackbar, I used a HF pipe bender, yes I know it's for pipe and def not for .250 wall dom....but it worked. That combined with shaving the diff cover got me the clearance I needed. I also checked...

Got some good work done this weekend and today. For the rear axle, got the antiwrap bar bracket and gussets all welded on, just needs brake/hub parts and gears installed snd it's done. For the front. I completely redid my frame coilover mounts. That meant going into the engine bay. But I am...

Havent updated this in awhile, but a lot has changed Now, onto the one ton stuff. The short list is Gm Kingpin Dana 60 from a Chevy V30, 14bolt from a late 70s truck Fox 2.5 12 inch travel coilovers, solid axle ind knuckles, spindles, steering arms, 5.38s, eaton e locker in the front, grizzly...

Set of 5 black mamba M14 wheels for sale 6 lug on 5.5 (139.7) 17x9 -12 offset have rock scratches and rash only have 3 of the center caps 1 wheel only had spare on it local pickup only in Indianapolis IN $550 obo New price $500

Got a bunch of parts in. Overhauling the steering system. PSC CBR pump, PSC reservoir, goatbilt relocation pump and fragola PTFE stainless steel braided lines. I'm going this route for a few reasons. 1. More pressure. 2. Remote reservoir, allowing for it to be mounted up high, and will help with...

Went to Moab for the second time in April of 2022, here are a couple of highlight videos Pritchett canyon video Going up hells gate

Awhile back I had orderd some chromoly rear axle shafts for the 10 bolt. These are from nitro gear and axle. https://www.nitro-gear.com/GM-8-6-Nitro-Rear-Axle-Shaft-p/axg40022632.htm I had originally put some factory oem wheels studs in them, however after I installed the axle shafts I...

The top and bottom angled portions for the middle plate, I struggled with getting good welds and grinding it smooth. So I used some JB weld to make it smoother. Mocked up with the grab handle and mirror.

This is what the height looks like with a human in the seat. It's pretty close to perfect, maybe a couple inches higher would be the sweet spot. I also started cutting and test fitting some if the top plates. Didn't get much further than that as I need to pick up some smaller diameter welding wire.

Did some more work on my half door. Worked on getting the inner and outer panels level, and test fitted it. Up next will be to cut the top piece and weld it on.

also started working on some half doors. Just doing the driver door for now. I got it all cut, next step is to get some sheet metal and weld a top to it.

Cranked through a lot of things in the couple of months before going to moab in April of 2022, but she's finally back on all 4s. New: -Yukon Chromoly axle shafts -diff cover bolts -wheel bearings -ball joints (both sides) -solid axle forged spindles (old ones looked wrong, like the bearing was...

I've been working on building a new crossmember up front. What I had before was just bolted to the frame and didn't add much structural support and mainly served to hold my power steering cooler. This new crossmember is welded to the frame so it should add some rigidity as well as holding my...

So upon further consideration I decided that the 18ga wire that I ran for the transmission cooler wasn't going to be adequate in the long term for the amps that the fan pulls. I only used it because it was laying around at the time. It's right on the edge of what would work, but I didn't want to...

Installed a license plate relocation bracket, since a Thorparts rear is on the way. The bracket includes a license plate lamp and a little brake light. I tapped into the wiring behind the drivers taillight Brown is the running lamp circuit (license plate lamp) Blue is the brake light circuit...

I finished installing a transmission cooler. Since I'm running a PS cooler up front that was albeit poorly located right below below radiator, I decided to do a remote mount trans cooler. This avoids adding more heat in front of the engine radiator and lows the trans cooler to be in a place that...