NPR 4wd conversion and camper build thread.

javajoe79

Fabricator
I got one upper spring perch finished. Turned out good. I have a plan for the shock mounts but I want to be further along with the spring perches first so once I have the lowers done and springs in place I will finalize the shock mounts.


22008313_1276501359126422_5231693423946123164_n.jpg


21766518_1276501369126421_1207442652343543279_n.jpg


21768062_1276501389126419_351181581516030086_n.jpg


22045787_1276501395793085_3928897717588841220_n.jpg


22007549_1276501429126415_5168847776614851820_n.jpg
 

DzlToy

Explorer
Do you know what length shock you will be running or how much wheel travel you are expecting?

I was quite surprised to see a 4Runner last weekend with a 12" shock and 28" of articulation. While you certainly don't need this on a camper or expo rig, it sure makes getting into the back country easier and more comfortable (read: further away from the Yuppies and Yayhoos, hopefully)
 

javajoe79

Fabricator
I'll have around 10" of travel per corner. The shocks have a bit more travel than that. Planning on limiting straps in the back so the shocks don't become the limiters. I feel like that's a good amount of travel. In the future though I may go for more but for now I'm trying to keep it simple and get it road worthy.
 

javajoe79

Fabricator
Just finished the other upper perch and both lower perches. Shock mounts and panhard bar come next and I will have a complete rear suspension. With the springs I chose, 565lb/in, They compressed half an inch as they sit with pretty much nothing mounted on the back of the frame yet. Target ride height is about 4.5" below where it is now so that means if I add 5000lbs I will end up at my target ride height, if I add more I can add spacers to raise the ride height, order taller springs, order stiffer springs or lower the upper spring perches by drilling another set of bolt holes. I have a feeling that I am going to be good as is. I don't plan on being too heavy but we'll see.

22007608_1277077765735448_7023399246281974482_n.jpg


22045704_1277077792402112_3268051318749610479_n.jpg


21765241_1277077799068778_9145272812382723736_n.jpg
 

Czechsix

Watching you from a ridge
Looks like there's going to be a ton of leverage working on those lower spring mounts. Did you think about doing a dead center mount on top of the axle? I think it would be much more robust, as far as the upper mounts you'd have to raise them, but you're doing a custom camper, so you can design plenty of room in there for the upper mounts....

Coil suspension should be awesome, this'll be a nice ride once you're done.
 

javajoe79

Fabricator
I'm not totally done with the lower perches actually. I am going to brace them up to the 4 link brackets. I agree, I would have liked the springs on top of the axle but I am limited on overhead height there as I am trying to keep the front top edge of the camper box about even with the cab roofline. That leaves me with about 3" of room above the frame rail for the upper perches. Plus the 4 link brackets are in the way too. I am looking forward to driving it. I may have to strap some dead weight to it to simulate the weight of the camper etc... once I get it road worthy.
 

javajoe79

Fabricator
Rear shock mounts are mostly done. Final welding and additional bracing to the lower spring perches will tie it all together. I was forced to tilt the shocks over backwards because I will be limited on overhead space once the camper box is mounted. This thing won't be fast so I think I'll be good. I have some ideas for adding additional shocks if needed in the future. These Rancho RS9000XL shocks are built pretty impressively not to mention very affordable. I'll have the same shocks up front too so I can minimize the spare parts I have to carry.

22448406_1294815193961705_8757683549943377158_n.jpg


22448563_1294815247295033_8569240143162200287_n.jpg


22554740_1294815420628349_6892994508016519788_n.jpg
 

SkiFreak

Crazy Person
Maybe a dumb question, but does the shock being at an angle have any noticeable affect on its efficiency/wear?
 

javajoe79

Fabricator
I've completed the rear suspension at this point. Next I am redoing the ugly and scary front leaf spring mounts and installing a U bolt flip kit. I will also be incorporating the shock mounts into the upper U bolt plates and modifying the stock NPR shock towers to accept the rancho shocks.

The pics show the rear suspension at near maximum ride height as there is no weight on the chassis yet.

23231510_1314040702039154_5183385281729433076_n.jpg


23434792_1314040705372487_2923835424566603686_n.jpg


23319455_1314040728705818_8470282663491467187_n.jpg
 

javajoe79

Fabricator
Recently I finished the leaf spring mounts and U bolt flip install. I reinstalled the axle to mock up the shocks and build shock mounts and limit strap brackets, then I will take it back apart to finish weld and paint it all. I also got a rear driveshaft made. It's starting to look like I might drive this thing this spring.

25398689_1351421324967758_1107587290075903802_n.jpg


25445935_1351421328301091_8187225816628921248_n.jpg


25594117_1351421378301086_4230026782944068744_n.jpg


25446326_1351427191633838_4046761792723486857_n.jpg
 

ScottReb

Adventurer
Thanks. Youre doing a great job! Really glad you came up with the supersteer piece. I could see something under RebelZilla but had no idea what it was, didnt know there was such an option to change push-pull.
 

Forum statistics

Threads
185,534
Messages
2,875,615
Members
224,922
Latest member
Randy Towles
Top