Page 1 of 2 12 LastLast

Thread: Removable winch mount in bumper?

  1. #1
    Join Date
    Jul 2017
    Location
    Truckee, CA
    Posts
    55

    Default Removable winch mount in bumper?

    I have a Montero and I would like to get some sort of (not fancy)lightweight steel bumper for the front and rear which has some sort of built in cavity where a winch could be optionally mounted in the front or the rear. Something like a reasonably light 4 or 6" channel iron bumper and having the winch mounted on a carrier with either one or two 2" square tube hitch mounts located at the rear of the bumper to allow for easy removal to be relocated to the front or rear. In all my searching I haven't found anything nearly similar and was wondering why something like that hasn't been designed. So in fact the front bumper would act as a "garage" for the winch to be used in that location or from the rear. Another option would be to have some sort of articulating plate mounted under the bumper which could be used to attach and articulate the winch in situations where the direction of pull wasn't directly in front, so the winch could actually "swung" one direction or another to assure a straight line pull.

    It doesn't make sense to me to have a permanently mounted winch on the front, because if you got yourself in a situation where you needed a winch, most likely you would want to be pulled out from the direction you came from and not the direction you are going. Having an option would be golden.

    If I knew how to weld, I'd build one myself, but alas I have to see if anyone else had similar ideas? I've searched and have found nothing.

  2. #2
    Join Date
    Feb 2007
    Location
    Littleton, CO
    Posts
    7,560
    Receiver mount? They have those.
    .
    https://www.finditparts.com/products...SABEgK3hPD_BwE
    .
    I could see putting the winch on the receiver (either front or rear) while traveling to or from your destination, then when the actual "off roading" started, put the winch inside the vehicle (so it doesn't affect your approach/departure angles.)
    .
    Keep in mind, though, winches are heavy sumb!tches. I could barely pick up the winch for my wife's Jeep after Amazon delivered it to me. It was a Smittybilt 8k winch and I want to say it weighed somewhere around 80lbs at least. 80lbs of winch + 25 lbs of receiver mount is a lot of weight to be moving around on a regular basis.
    Martin
    2004 Chevy Suburban 1500 LT in "Expedition White"

    Having a Suburban means never being able to say "We don't have room for that."

  3. #3
    Join Date
    Jul 2017
    Location
    Truckee, CA
    Posts
    55
    Quote Originally Posted by Martinjmpr View Post
    Receiver mount? They have those.
    .
    I could see putting the winch on the receiver (either front or rear) while traveling to or from your destination, then when the actual "off roading" started, put the winch inside the vehicle (so it doesn't affect your approach/departure angles.)
    .
    Keep in mind, though, winches are heavy sumb!tches. I could barely pick up the winch for my wife's Jeep after Amazon delivered it to me. It was a Smittybilt 8k winch and I want to say it weighed somewhere around 80lbs at least. 80lbs of winch + 25 lbs of receiver mount is a lot of weight to be moving around on a regular basis.
    I know they make the winch carriers. I use the milemarker 10,500 lb hydraulic winch set up through winches plus at my mining claim. I am a 62 yr old guy and don't have much trouble moving the winch carrier around a boulder strewn river bed, so walking from the front of the truck to the rear isn't a problem. The question was has anyone ever seen a front/rear bumper set up where you can easily remove the winch from the front to the rear as needed? I have some ideas, but I was wondering if anyone has a better idea than me. I have a "spare" 12,000 hydraulic winch which I may consider to use if it doesn't push my front end down too much. Otherwise I may have to use an electric winch. I really, really like my milemarker/winches plus set up. I have literally 500 hours on it and have never had a problem. I use it all day long winching rocks all over the place and it never misses a beat.

  4. #4
    Join Date
    Oct 2017
    Location
    Midwest
    Posts
    16
    Some random thoughts. In the front and rear you would probably build a bumper out of tube that would both go over and under your winch. You would have to crawl under the rig in order to install and remove the pins holding the winch in place. In the rear you would probably lose your trailer hitch and a new one would have to fabricated to wrap under the winch. Crawling under the rig to switch from one end to the other might range from annoying to impossible depending on the terrain and how bad you are stuck. With the current loss from the front to back of vehicle I would probably try to have a 2nd battery back there. You would end up with entirely new bumpers front and rear. I would think paying a fabricator to do such a project would cost between 3k and 4k.

  5. #5
    Join Date
    Jul 2017
    Location
    Truckee, CA
    Posts
    55
    So it looks like I need to put my thinking hat on. I know it can be done without having to crawl under the vehicle, I just need to get creative. I'm kinda bummed that no one has attempted this before. I am thinking a channel iron bumper with a cut-out dead center in front of the vehicle for the winch carrier to slide in. It wouldn't be hard to make some sort of lever locking pin that would lock the winch in the 2" tube from the front of the vehicle. Many moons ago I had a custom winch bumper on a 1979 Toyota I used to own, where it also was a channel iron bumper and the winch was nestled dead center, but what I did on either side of the winch was to create lockable boxes built into the winch bumper where I could store tow straps, chains, D rings, etc and it worked great for years. The bumper stuck out maybe 6" further than stock. I had a Tensen winch on it and used it almost daily to move around my commercial woodsplitter. I'd like to do something similar to that with this iteration. Hmmmmm.

  6. #6
    I have seen a couple of people do something like this. One idea was the winch sat on a plate and had 2 receiver tubes mounted to the bottom. The winch sat in the space between the bumper and the frame, and was locked in place with two x 2" long square tubes going through the bumper, though the receiver tubes on the winch mount, then into the crossmember. So the 2" tubes basically acted like really long pins. On the rear I don't remember if they had the same setup or pinned the locking tubes into the mount and just used it as a dual receiver mount cantilevered out back. But it looked like a much stronger design than just a normal receiver mount.

    The most interesting idea I saw used a center mounted winch under the tub facing the rear. The cable would wind out the back, go through a snatch block, then run back under the vehicle through some pulleys or guides and exit out the front. When used it as a front mounted winch, the snatch block in the rear would be pinned in place, the cable would run through the snatch block, turn around and go through the front fairlead and it would act like a normal winch. To use it as a rear winch, the winch cable would be anchored in the front and the snatch block in the rear would be unpinned and used for rear recovery. So rear recovery was always a double line pull. Seems like that would be easier than moving a winch back and forth.

  7. #7
    Join Date
    May 2011
    Location
    Utah
    Posts
    6,450
    The guys over at ADD sell a hidden front mount that goes behind the stock bumper, while it is not removable it is a great setup. Since I bought my first Jeep in 1999 there has been one occasion where I needed to be winched from the rear, I was with other people and they pulled me out just fine.
    1998 Montero with winter/locker package with Old Man Emu springs/torsion bars/shocks, ARB winch bumper, 33x10.50 km2's, aluminum roof rack with ARB awning

  8. #8
    Join Date
    Jul 2017
    Location
    Truckee, CA
    Posts
    55
    Quote Originally Posted by jeep-N-montero View Post
    The guys over at ADD sell a hidden front mount that goes behind the stock bumper, while it is not removable it is a great setup. Since I bought my first Jeep in 1999 there has been one occasion where I needed to be winched from the rear, I was with other people and they pulled me out just fine.
    Good point... don't get in those sort of situations when you are alone.

  9. #9
    Join Date
    Jul 2017
    Location
    Truckee, CA
    Posts
    55
    Quote Originally Posted by ducktapeguy View Post
    I have seen a couple of people do something like this. One idea was the winch sat on a plate and had 2 receiver tubes mounted to the bottom. The winch sat in the space between the bumper and the frame, and was locked in place with two x 2" long square tubes going through the bumper, though the receiver tubes on the winch mount, then into the crossmember. So the 2" tubes basically acted like really long pins. On the rear I don't remember if they had the same setup or pinned the locking tubes into the mount and just used it as a dual receiver mount cantilevered out back. But it looked like a much stronger design than just a normal receiver mount.

    The most interesting idea I saw used a center mounted winch under the tub facing the rear. The cable would wind out the back, go through a snatch block, then run back under the vehicle through some pulleys or guides and exit out the front. When used it as a front mounted winch, the snatch block in the rear would be pinned in place, the cable would run through the snatch block, turn around and go through the front fairlead and it would act like a normal winch. To use it as a rear winch, the winch cable would be anchored in the front and the snatch block in the rear would be unpinned and used for rear recovery. So rear recovery was always a double line pull. Seems like that would be easier than moving a winch back and forth.
    That's an interesting idea.... the problem being that you would have to have access under your vehicle in order to determine direction of the pull. That's a scary thought.

  10. #10
    Join Date
    Sep 2009
    Location
    Australia
    Posts
    132
    My winch is mounted on a cradle that fits into a standard HR style hitch receiver. I have one each end.
    It can also be used "remotely" and that has many advantages.
    The down side is that it is a Warn 16.5Ti and weighs about 70kg.
    05-05 Last, paint, tanks etc 058E.jpg
    07-10-19 to 23 009Ec.jpg
    Cheers,
    Peter OKA196 motorhome
    Attached Images Attached Images
    ......................Enjoy.....................
    OKA196, 4x4, DIY, self-contained motorhome. http://www.oka4wd.com/xt196.htm

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •