Recent content by haqi

  1. H

    Black Series HQ Tips, Tricks, and Learning.....

    I recommend you to join Black Series owners Facebook page. There are lots of threads on this. https://www.facebook.com/groups/597325343973738/?ref=share
  2. H

    Black Series HQ Tips, Tricks, and Learning.....

    Thanks Paul. It was because of you that I started looking at the right places. There is always a first :). The quality of wiring is terrible and no labeling or map of how things are wired. I also think many appliances aren’t well protected based on how things are wired. But I have learnt so much...
  3. H

    Black Series HQ Tips, Tricks, and Learning.....

    Update! I just got the relays from Oreily and everything is working fine now but I will replace the relays with the Victron BP as soon as it arrives. Both relays were apparently dead (stock one in my hand). Thanks for all your help.
  4. H

    Black Series HQ Tips, Tricks, and Learning.....

    Hi Paul, I did all the above and I do get 0 Ohms on the black wires to the ground bus. Checked both if them. Also all corresponding pins have 13v. The control panel still won't get power through these relays. Not sure what that means but I checked resistance on the relays as well and don't get...
  5. H

    Black Series HQ Tips, Tricks, and Learning.....

    I did actually check the relay pins after taking off connectors. They have dc. I need to do the backtracking to the bus bar with black wires. I will report on this tomorrow. Thanks again.
  6. H

    Black Series HQ Tips, Tricks, and Learning.....

    Tha Thanks Paul. I will check this tomorrow. If not I will just get rid of the relays and use a 50 amp switch instead. It seems like too much hassle and not much use in drawing power all the time with these relays. I appreciate your help! Thank you!
  7. H

    Black Series HQ Tips, Tricks, and Learning.....

    Update! I disconnected the 7AG from the breaker and reconnected. Now has power and was able to connect it directly to mains switch and everything turned on. But when I connect it to the relay it doesn’t power the control panel. Does that mean the relay has gone bad? Thanks.
  8. H

    Black Series HQ Tips, Tricks, and Learning.....

    Hi Paul, This cable doesn’t seem to have power at the control panel end but has power at the breaker. I am wondering if there is anything in the middle somewhere that’s broke or the wire itself has gone bad? What do you reckon? when I feed the pump line to the main switch everything works...
  9. H

    Black Series HQ Tips, Tricks, and Learning.....

    Is is the one on the control panel breaker in the battery compartment?
  10. H

    Black Series HQ Tips, Tricks, and Learning.....

    Ok then I was doing it wrong. I took the tape off of the other one and that cable has no power. See attached pic. It’s labeled yellow 20e on it. Does this mean that battery connection is bad? I see that wire on the battery terminal. Thanks
  11. H

    Black Series HQ Tips, Tricks, and Learning.....

    Hi again, i found the problem it’s this wire labeled N20a which I have no idea what it means (attached pic) that goes to the main switch that doesn’t have power but it says 14AWG I tried to backtrack to the battery and I can’t see any wire that’s 14AWG all small ones are 12AWG. I tried using...
  12. H

    Black Series HQ Tips, Tricks, and Learning.....

    Thank you so much. I will do this today. It may be that the relay itself is not working so I will check the resistance on them as well. Thanks for the tips regarding where to put the multimeter. I have turned off the battery and the stair doesn’t work work so that’s confirmed. When I do turn off...
  13. H

    Black Series HQ Tips, Tricks, and Learning.....

    Exactly what I am thinking. On the bright side once I find it I will have much better knowledge of the wiring.
  14. H

    Black Series HQ Tips, Tricks, and Learning.....

    I tested it with the generator and I have never used shore power since I got this camper.
  15. H

    Black Series HQ Tips, Tricks, and Learning.....

    Yeah that was the first thing I checked and it is working fine.
Top