Recent content by Iain_U1250

  1. Iain_U1250

    Lean angle, Roll.

    On ours Unimog U1250, we have recently gone over 35 degrees, but the was turning at the bottom of a dune on an entrance to the beach and we had a sand wall on the one side so that we could not really fall over, but we didn't hit it, just hanging on was difficult for my co-pilot. We try not to...
  2. Iain_U1250

    Unimogadventures - Our build and travel thread

    In addition, I have refurbed the back axle, with new diff lock seals, new seal in the torque tube and new bearings and seals in the portals. This should be good for another 9 years or so. I also have a new custom rear sway bar - it is 39mm compared to the original one being 32mm. mm...
  3. Iain_U1250

    Unimogadventures - Our build and travel thread

    Finished my new exhaust, 4" from front to rear. It is quite a tight fit, so I have added a lot of extra hangers to stop it moving around. I have two flex joints, as the movement will be concentrated in the section between the engine block and the camper subframe. I have a semi rigid...
  4. Iain_U1250

    Introduction, Tuning/Uprating Story And How I Got here

    Hi, not offense taken, all good discussions are great. I have official Bosch technical manual for the inline fuel pumps, it covers everything on these pumps in detail. One section here below: The LDA doesn't increase the fuel beyond the full load - I've highlighted the section. I also...
  5. Iain_U1250

    Unimogadventures - Our build and travel thread

    A bit of an update. Since the rear axle is off, and I am still waiting for some seals, I'm doing a lot more of the other things on the truck that need doing. The turbo dump pipe I made 10 years ago cracked, probably due to the weeks of chassis twisting we did on this trip. I'll make a new...
  6. Iain_U1250

    Introduction, Tuning/Uprating Story And How I Got here

    Hi, welcome to the forum, I've been down the "more power and speed" road, and settled down to around 200hp, up a bit from the original 125hp in our 8 ton Unimog U1250. I could make a bit more by turning up the fuel screw on the pump, but my goal has always been reliability reducing fuel...
  7. Iain_U1250

    Unimogadventures - Our build and travel thread

    Two $28 seals let go and and you have to take the whole back axle apart
  8. Iain_U1250

    Unimogadventures - Our build and travel thread

    I did some more data manipulation of the records. Because we don't fill up the tanks when they reach any particular level, and sometimes don't fill them completely if the price is high and we know it is cheaper in the next town, the records of each tank give pretty strange results. With the...
  9. Iain_U1250

    Unimogadventures - Our build and travel thread

    Not really sure, but could have been when we were doing a lot of long highway trips at high speed. The first lower consumption would be when we were running the new engine in, and had turned the boost down. Since we fitted the new transmission around 60,000km things seems to be pretty steady...
  10. Iain_U1250

    Unimogadventures - Our build and travel thread

    and the matching fuel consumption
  11. Iain_U1250

    Unimogadventures - Our build and travel thread

    Just downloaded all of our track files from out various trips around Australia, still got a few more places to visit
  12. Iain_U1250

    Unimogadventures - Our build and travel thread

    A half day cutting any polishing and it has made a big difference. I'll wait until I get back to do it properly with the polishing machine. Just can't reach up here.
  13. Iain_U1250

    Unimogadventures - Our build and travel thread

    Thanks, not much to repair. Most of the scatches will polish out, as I used an industrial machinery paint not a car paint. Will do some hand polishing with a heavy cutting compound today. Our camper has a 2mm thick aluminium skin, not fridge box material so is pretty tough, we have a few...
  14. Iain_U1250

    Unimogadventures - Our build and travel thread

    Some of the realities of driving a large truck on tracks created by much smaller vehicles. I would not to have even tried these tracks without the extensive bar work we have,and our truck is smaller than most Unimogs. The angled roof helped a lot, without it, we would have had to do a lot...
  15. Iain_U1250

    Unimogadventures - Our build and travel thread

    It was on the way to Nor 6 memorial and the blowholes at Zuytdorp cliffs
Top