2004 Tacoma SAS

8sixFabrication

Active member
It's been a while since I have posted any updates, so I figured it was time, considering I have been working on the truck to prepare for the Rubicon later in August.

Back in May, I drove down to Vegas to meet a buddy for his 40th. While we were down there, we decided to run an easier trail called Tie Rod Canyon. Since we were alone, we wanted to do something less risky, even though there was another one I had my eye on. The truck did fantastic, and didn't skip a beat.

54690259841_c86df868f2_b.jpg

54690484688_d755451553_b.jpg


At some point, I got on the pre-order list for an upgraded carrier bearing from JXB, and got it in mid June. So I promptly installed it. Due to the mount being damaged back in January on the trail, the bearing is a little off. So the dust shield has been self clearancing into the bushing haha. I need to cut the mounts off, and make replacements, and re-align the bearing. But for now, It's stronger and better than the O'Rileys special haha.

54690508434_da75d2422e_b.jpg

54690248721_9529d4fe9e_b.jpg


About a month later, I worked on the winch line. I need to re-tie the end to work with the Yankum fairlead. I'm pretty happy with the way it turned out

54690582435_f71b98ab5a_b.jpg

54690248641_70f79929f3_b.jpg

54689428502_8c3d609d4a_b.jpg

54690248406_a2d06f41ed_b.jpg

54690473498_f652c590bc_b.jpg
 

8sixFabrication

Active member
The next thing I did, was make a little "platform" for the rear area in the cab, and change around some stereo components to save some space. This allows us to utilize the space better on longer trips, and provide some better storage. I have another piece I am going to make, to add on, that will make a great spot for extra drinks and snacks on road trips.

54690473363_7f7e2657f8_b.jpg

54690248131_ba4a1612b8_b.jpg


Next, I moved onto repairing the tie-rod that got bent back in Jan. I had to resort to a mildly sketchy means of pulling it straight, but it got the job done.

54690473248_a4872c3cee_b.jpg

54689428257_c0cb4f4c05_b.jpg

54690497469_1d9421e84c_b.jpg
 

8sixFabrication

Active member
One of the last things I "need" to do, in preparation for the Rubicon was get the fuel tank skid plate repaired. I opted to just buy an Amazon special one. I also had been eyeballing the Eimkeith fuel tank relocation kit for a while, so I ordered it a while back. It's meant to raise the tank 2".

Unfortunately, it took forever to get the kit from Eimkeith, and the communication was really bad. He was extremely difficult to get responses from, and when I finally got the kit, there was no instructions with it and I couldn't find anything online. And, as expected, the emails and messages I sent asking for support, went unanswered. The mount for the tank was pretty easy to figure out, but the optional evap canister kit that I added had a few pieces that I have no clue what they do.

Between the horrible customer service, and deciding that while I have the bed off, I wanted to box in the frame, I decided to bail on the kit and just make my own stuff. I was pretty disappointed, because the quality is great. I used his lower link relocation brackets on our 80 series and it was a good buy, but unfortunately I have lost trust in him and will be returning or selling this kit.

So after receiving the kit last week, I got to work pulling the bed off on Friday.

54690581830_dfdb004dff_b.jpg


The following morning, I got a better look at things. After staring at it for a while, I decided that I wanted to just push forward with boxing in the frame. Getting the cross member out for the fuel tank was a pain, but I eventually got it out. The rear I had to cut out. Before I did that, I tacked in some supports to maintain the width of the frame.

I also cleaned up the rust the best I could, and painted all the parts that would be covered by the boxing plates


54690473153_6081279e7d_b.jpg

54690247776_889e54d826_b.jpg


I used a straight edge across the bed mounts on the frame, to mark a vertical line, and reference off some of the mounting holes, so I knew where to locate everything once the crossmember was out

54690473058_80788cd924_b.jpg


The following day I got some Cad-Board out and made some boxing plates out of 1/8" plate. The frame is made of about .090" thick material, so I figured this was a good balance. The back sides got painted to help reduce rust on the inside of the frame. Then they got tacked into place.

54690472968_04b708a233_b.jpg

54690581615_a4da4e050a_b.jpg


I decided to take Monday off to take care of some things at home and make more progress on this. I got the plates all welded in, the fuel tank cross member modified and welded in, and made a rear crossmember that got welded in.

54690497134_e972387f3b_b.jpg

54690497184_e923aa5e12_b.jpg


Last evening I added a couple little fill plates to wrap up, boxing in the frame, then painted everything.

54689427737_233a7c3c04_b.jpg


And lastly, tonight I cut out the flange that the fuel tank bolts into, and made a real simple replacement that sits 2" higher. That got painted after.

I am hoping to have this wrapped up this weekend, with the bed put back on and back on the road.

More to come

54690472583_cea17afd9a_b.jpg
 

Forum statistics

Threads
189,921
Messages
2,922,190
Members
233,083
Latest member
Off Road Vagabond
Top