Search results

van with AdvanceTrac RSC and Flex fuel. This is a 4x2 with a basic interior conversion. The interior has a classic design with bed in back with plenty of storage under the bed. There is a cabinet with 3 large drawers (lots of storage). There is a sink cabinet with hand pump faucet and 5 gal...

Done, thanks

Original owner. 3 gas tank storage racks on full mesh front tongue area. Spare tire Weight: 507lbs Registered 2015 inside Width: 58.5" Fender to Fender Width: 78" Inside Height: 42.5" Exterior Height: 68" Floor Length: 81.5" Overall Length: 148" Inside Length: 92" Receiver Size: 2" Hatch...

Original factory Leaf springs set is off my 2000 2.4 L Extended Toyota Tacoma, I am the original owner. Call @ 480-381-5312 $400 for pair West Valley - Goodyear, AZ

I have a 2000 Tacoma extended cab, 2.4l. Does anyone have a recommendation for front coil springs. I'm looking at OME coils and there are some options: 881 coils - stock front weight- uses top plate spacers 883 coils for an additional 100LBS front weight (can also be used for 3" lift without...

similar rigs Nice stuff, check out my blog: http://www.duningartist.blogspot.com Enjoy!

My build Toyotas are awesome 4x4 veh. Just thought I'd post my blog because if you scroll thru you'll see my build. I opted to build a inside platform for storage purposes with an interior accessible compartment for "not so used" items. In the extended cab, you'll see that I build a cabinet...

Just finished my interior build, getting ready for a trip to Oregon via as much off-road between AZ to OR as possible. May start with the Lake pleasant to Wickenburg trail. By the way we are leaving on Dec. 26th to head out about 8:00 am front near the north entrance of Lake Pleasant to start...

Awesome, enjoy your travels. Another architect's adventure and build: http://duningartist.blogspot.com/

Oxygen / Acetlene Harper Set with gauges and cutting torch. Tanks are 36" high and 24" high. Asking $500.00

Hypertherm Powermax 600 Plasma Cutter used just a few times. 220 power requirement. Cuts up to 3/8 steel. I recommend researching online for price comparisons and specifications. Asking $1,100.00

Custom made welding, cutting and work table, dimensions: 30" wide x 48" long x 3'-0" high, This table is protable, wheels on one side and handles on the other for moving. Bottom metal shelf is removable. Asking $275.00

Model 1997 29RQ Winnebago Minnie Winnie Series 300 29ft with just under 44000 miles It has an onboard onan 4000 generator. This is a mid kitchen model an has all the std. RV features, microwave, 3 burner stove and oven, furnace, water heater, water pump, LP tank, exterior radio and shower...

Are you selling the trailer shown in the photo and if so how much?

CA budget If they legalize cannibus then their troubles are closer to being over. My bet is; its going to happen....its all in the numbers and the numbers look good.

SwiCage I'm with you, I had the same idea, like the slides braces. I think all those factory RTT's are very nice but to pay so much.....there just tents, no way. This build makes so much more sense. :bowdown:

After posting my question I went back thru the posts and saw the answer to my question but thanks for responding anyway. If you were to put back the spare it would be lower, correct? You have some wonderful ideas and you are very inspirational for others, thanks

optional storage If you don't need hard shell storage but still need WP storage, rafting bags are really awesome and rugged but not modular.

roamingaz I was just mentioning this to my parter this morning for those long distance excursions. Did you install the tank where the spare usually goes? How is it held up? and how do you connect std tank w/ new tank? :clapsmile

I understand that the ones sold by ARB or Engle are a good size and have little drawing from your electrical system, I too am not an expert.