Search results

Heat of summer I usually switch out the Carhartts for the lighter weight Kuhl’s (that pucker really badly) or the Wrangler “flex” pants. Sent from my iPhone using Tapatalk

This is a great thread. There are apparently a lot of us thinking this same thing! I switched from Jeans to Carhartts and Kuhls about 6 or 7 years ago. I literally have probably 10 pairs of Kuhl pants hanging in my closet all in the same color and it drives my wife crazy. I have to say...

Keep the fridge in your tow vehicle. Mount it to a slide and wire it in place. Hard mount a small “solar generator” (a misnomer) such as a Jackery 500 and put a 100w panel on the roof. Slide + battery + panel will cost you about $900 but you’ll have a setup that will be extremely versatile. I...

Not mine, but I've seen this one for rent https://www.outdoorsy.com/rv-rental/los-angeles_ca/2019_off-grid_expedition-2-0_145172-listing I think thats exactly what you're looking for, isn't it?

Thanks for that clarification. Going back to my original post, I really was just looking for a good propane grill (already have several small portable charcoal grills that I really like). Sounds like the Volcano 3 is. very versatile, but better as a wood/charcoal grill than propane. Thanks...

So the Volcano was sold out over the holidays, so I ended up getting a Napolean Travel Q 285 for Christmas. It really works extremely well and its so easy to use I'm even using it at home instead of firing up the Weber Performer charcoal grill (that I have used exclusively for over 20 years)...

Thats disappointing to hear. I think many of us have considered Rhino's products to be one of the higher quality options out there, but as often happens, popularity can lead to a rush to supply the demand, which then leads to quality problems. Perhaps that is the case here.

That’s a great idea. When I get back to my trailer this week I will set it up and take some pix for reference and do some thinking along those lines. Sent from my iPhone using Tapatalk

I’ll have to look into the viability of that approach. I think that there is so much direct overhang that I’d need a 90° bend (vertical) immediately after the lower insertion, then about 8-10” of rise, then a return 90° (horizontal). I doubt there’d be enough length at that point to actually...

Thats actually a really good point. It could certainly be the issue. That being said, I drove for 3+ hours without turning off the ignition and it was still calibrating when I pulled off the highway and onto the dirt road approaching my camp...

I thought about using brass or stainless grommets (I have a kit with punch/press for my boat) but I worry about the noise of the grommet sliding around on the spring pole in a slight breeze. Noise like that drives me nuts...

Ah fair enough. "Old Jeep wheels" then. :-) GLWS, looks like a lot of work went into it!

Looks like a neat build. Btw, Jeep wheels are “5 on 5-1/2” if that’s what you meant. Sent from my iPhone using Tapatalk

I may have bro do that. One of the questions is how to best reinforce the holes in the awning. I seem to recall seeing iron-on fabric reinforcements somewhere and wondering if they will stick... Sent from my iPhone using Tapatalk

That switch panel looks nice. I thought about running this off my SPOD knock-off but instead utilized the power coming from the 12v outlet using one of these that had been powering a CB (which I’ve since removed after going the ham route) https://www.quadratec.com/products/96080_9801.htm Sent...

I've found the single biggest effect (other than supplemental heating) is the layer UNDER me. You can pile all the blankets in the world on top of you, but if you don't have a good insulation layer under you, it won't help. Another thing that has served me well in cold weather is sleeping in...

I'm sure this must be a common issue - how do people typically deal with the fact that in many scenarios (like mine) the 270º awning prevents me from being able to deploy spring poles on two of the three windows. Or if I want spring poles (such as in a winter camping scenario) I just have to...

Not sure if you're doing it in a Jeep, but I found that it fit very well on the metal bracket just behind the removable "knee panel" on the driver's side. I then installed the switch using the REDARC switch panel into the little "vent hole" that is unused (at least in the rubicon). It was a...

So for anyone following this, I'm working up a proof of concept with some scrap I have laying around from previous projects. The sliders will be 30mm aluminum bar stock, about 25 cm long (though my diagram is marked 29mm, that slot is actually more like 30.6mm in width). They will be fastened...

Ah good to know. Redarc publishes good material but no where do they mention that this calibration can take many hours over many days! I was worried about my wiring being somehow off. Thanks! Sent from my iPhone using Tapatalk