Search results

I’ve never really cared much about a couple inches difference between my tow vehicle’s hitch and my trailer tongue height but now that I have a Turtleback I’m trying to get it to sit level while hooked up. With my setup that means I need a 0” drop mount for my Max Coupler. I have a 2” drop mount...

I'm looking for a propane BBQ to go with my new trailer. Its not a big trailer so I need something compact. Here's my general set of requirements: Compact size - maybe folding legs? Propane - ability to run off 5 lb tank w/ adapter hose Ability to get hot enough for a good char/sear, but...

Has anyone installed a redarc controller? I’ve got the factory 7-pin harness sitting in a box and a Redarc and I’m planning out the install but the instructions are confusing me a bit. 1. The Mopar harness appears to NOT carry the brake switch signal, only the “blue wire” that activates the...

Just ordered an iSUP and wondering if I should spend $35 in a schrader-Boston adapter and use the ARB (single cylinder) compressor on the Jeep, or just spring for the $100 dedicated inflator for such toys.. I know that I'll have to be very careful with inflation pressure if I use the ARB...

over the years I have collected half a dozen inflators and tire gauges, both analog and digital. My problem is that few of them match and I don’t have a “reference standard” with which to calibrate them! To make matters worse the TPMS in my Jeep rarely matches any of them... I’m curious if...

Because of the way I have my Jeep set up (plywood deck and hard-mounted fridge slide and cargo retention system) everything fits perfectly (no wasted space). This means I don't have room for an off-the-shelf "bolt on" tailgate table (or I don't want to run the risk of it not fitting). I also...

In case anyone bought the 3-bar Rhino Backbone + Vortex Bar kit but has decided that they only need 2 of the bars, I'm looking to add a third bar to my 2-bar Rhino Backbone system. Specifically the parts I'm looking for are: (2) Rhino-Rack RLCP Leg Kit for Backbone System - 1-1/2" Tall - Qty 4...

For those of you who prefer "Made in America" the folks at Ace are now making a roof rack for 4 door JKs. It looks very nice, and uses its own brackets for a very low-profile mount. https://aceengineeringandfab.com/collections/jk-products/products/jk-roof-rack-4-door I've reached out to them...

That seam just forward of the cargo track in the right hand photo is where the rear seat would normally mount, so at the bottom it would clear, but because of the angle of the rear seatbacks you probably won't be able to use the Wolf Packs two deep if you still have the rear seats installed...

I want a rear rack/shelf to elevate my lighter weight items like clothes and sleeping gear, and I need it up high enough to clear my Dometic 50 fridge. The problem I'm running into is that all of the ones I can find rest on the sides of the tub where the hard top attaches. The problem is that...

In their infinite wisdom, Rhino only makes these legs available in packs of 4 and 6 (to have two or three bars). I didn't think I'd need 3 bars originally so I bought a 4 pack. Now I want to add a third crossbar, but they are telling me I have to buy a minimum of 4 of them ($170) when all I...

As I've posted in another thread, I'm running the Dometic fridge in my 4-door Jeep powered by a Suaoki G500 lithium power supply (500WH unit for $389 on Amazon). I have a 100w HQST panel mounted to a Rhino Vortex rack using some L-brackets that I fabricated. Components of my setup: (not...

I've just mounted a 100w panel to my roof rack for when I'm traveling. My plan is to attach the leads to a bulkhead connector of some sort in the fiberglass roof of my Jeep, with a connection on the other side going to a portable battery pack. I want to be able to easily plug and unplug the...

It seems that most of the fridge slides I'm seeing are several inches wider than necessary to accommodate the 26" x 18" footprint of the CFX50. (this is including the now discontinued Dometic slide). The DFG Offroad unit looks like it might be nice, but they don't post the dimensions and its...

Asking $450 $400 for the entire lot. No shipping (too heavy!), but I go back and forth between San Diego, Santa Barbara, and Monterey frequently so could meet somewhere in between. Would prefer to sell as a set, but if you just want one of the items, let me know Rock Krawler Front Adjustable...

I've been poking around considering various options for powering my Dometic CFX50 fridge, and I think I want to go with one of these portable "generator" type units that have everything built in. My plan is to keep the unit plugged into the IGN-powered 12v, and then plug the fridge into the...

http://www.overlandpros.com/index.php/product/panamint-2000/ Looks like a lighter weight knock off of the OZtent and less than 1/2 the price (on sale right now for $325 - that seems too good to be true). But I wonder about materials, construction quality, and after sale support (accessories...

After a lot of research I've decided to pull the trigger on a Rhino Backbone system for the Jeep. I will start out with a pair of Vortex bars - since I have a Sunrider top, I can't use the full sized Pioneer platform, and honestly I'm not sure I'll ever really need a $1,000 platform when I...

Complete Tiregate "Adventure Series" spare carrier with Dual jerry can mount and license plate relocation kit - $700. I spent over $1,400 on this setup, used it once for a trip to Baja. It mounts to a Class IV receiver hitch and then tightens in VERY securely so that it does not rattle AT ALL...

I posted this in the Wrangler forums because I received a lot of questions from folks on how I put this together. In case there are some folks here that don't frequent the JK section in Wranglerforum.com I figured I'd post it here too. ------------------------- If you're looking for a way to...