TheWenlock
New member
Additional Info:
-Built 2 years ago.
-Tig welded cracks around power steering, fabricated custom front tow hitch receiver bracket that ties into JCR unibody reinforcement brackets. 5.25” front lift 5.5” rear.
-Is incredibly smooth to drive off-road with the drop brackets, 60/40 travel (more like desert rig), all poly and suspension lubed with 2-4-c Teflon grease.
-All new steering with extensive upgrades.
-All new pullies belt water pump etc, cooling system converted to open system, all new hoses, fluid flushed, heater works great, upgraded fan and clutch(will not over-heat idling in 95 degree sun.
-I tried so i would know if electric fan wiring and relay were good, but couldn't get it warm enough).
-Clutch is good, 5 speed all gears shift perfect, 4x4 works, t-case has new fluid timing chain, slip yoke eliminator, cv rear driveshaft.
-If things didn't get installed with blue Loctite they got a combination of copper anti seize and marine grease(steering etc).
The Bad:
-It could use a new junkyard drivers door or parts and the blinkers are not working (was this way when i got it, all windows roll up and down fine).
-The paint job is faded in places
-Well over $6500 into build in parts alone.
-Had 29” tires when I got it, hadn’t been wheeled.
-Will add more pics of the interior and underbody for parts over the weekend.
Parts List:
-RT Off-Road Slip yoke eliminator kit #rt24005
-Flowmaster super 44 muffler
-Rubicon axle shims (steel) #re1467
-Rugged Ridge transfer case crossmember #12035.60
-Flex-a-lite fan #5915
-Omix fan clutch (for zj) #17105.03
-Alloy usa t-case chain #11650
-Rough country cv rear driveshaft #5076.1
-Smittybilt xrc rear bumper #76850
-Moog tie rod #d51312
-RuffStuff y-link steering delron
-Bilstein shocks 5100 series #33-066868, and #24-188197
-Hayden power steering cooler #676
-Rubicon track bar #re1670
-Rubicon 5” rear shackles #re2700
-Procomp sway bar end link kit
-Prothane poly sway bar bushing #1-1104
-Rubicon rear leaf (5.5” lift) #re1462
-Rubicon pitman arm #re2500
-Track bar bracket #re1665
-Track bar front #re1600
-Rubicon 4.5” lift coil springs #re1310
-Skyjacker .75” red poly coil spacer
-Rugged ridge heavy duty steering support 18021.05
-Rustys offroad stainless steel brake lines (red)
-Cardone power steering pump #20-37776
-Acdelco waterpump #252-191
-Rocky road: drop brackets, fixed lower arms(rubber bushings), upper arms (adjustable rubber bushings), bar pin eliminators for shock mounts
-Tomken machine gastank skidplate
-Stinkyfab transfer case bracket with soft durometer poly bushings
-Bulletproof poly engine mounts with soft durometer poly stinkyfab bushings
-BFG 32” Mud Terrain T/A KM2 lt265/75 r16
-Dodge durango power steering box remanufactured(forget the brand but at the time it was the only company doing quality work, was $300+)
-JCR offroad unibody tie in kit with power steering brace
-Built 2 years ago.
-Tig welded cracks around power steering, fabricated custom front tow hitch receiver bracket that ties into JCR unibody reinforcement brackets. 5.25” front lift 5.5” rear.
-Is incredibly smooth to drive off-road with the drop brackets, 60/40 travel (more like desert rig), all poly and suspension lubed with 2-4-c Teflon grease.
-All new steering with extensive upgrades.
-All new pullies belt water pump etc, cooling system converted to open system, all new hoses, fluid flushed, heater works great, upgraded fan and clutch(will not over-heat idling in 95 degree sun.
-I tried so i would know if electric fan wiring and relay were good, but couldn't get it warm enough).
-Clutch is good, 5 speed all gears shift perfect, 4x4 works, t-case has new fluid timing chain, slip yoke eliminator, cv rear driveshaft.
-If things didn't get installed with blue Loctite they got a combination of copper anti seize and marine grease(steering etc).
The Bad:
-It could use a new junkyard drivers door or parts and the blinkers are not working (was this way when i got it, all windows roll up and down fine).
-The paint job is faded in places
-Well over $6500 into build in parts alone.
-Had 29” tires when I got it, hadn’t been wheeled.
-Will add more pics of the interior and underbody for parts over the weekend.
Parts List:
-RT Off-Road Slip yoke eliminator kit #rt24005
-Flowmaster super 44 muffler
-Rubicon axle shims (steel) #re1467
-Rugged Ridge transfer case crossmember #12035.60
-Flex-a-lite fan #5915
-Omix fan clutch (for zj) #17105.03
-Alloy usa t-case chain #11650
-Rough country cv rear driveshaft #5076.1
-Smittybilt xrc rear bumper #76850
-Moog tie rod #d51312
-RuffStuff y-link steering delron
-Bilstein shocks 5100 series #33-066868, and #24-188197
-Hayden power steering cooler #676
-Rubicon track bar #re1670
-Rubicon 5” rear shackles #re2700
-Procomp sway bar end link kit
-Prothane poly sway bar bushing #1-1104
-Rubicon rear leaf (5.5” lift) #re1462
-Rubicon pitman arm #re2500
-Track bar bracket #re1665
-Track bar front #re1600
-Rubicon 4.5” lift coil springs #re1310
-Skyjacker .75” red poly coil spacer
-Rugged ridge heavy duty steering support 18021.05
-Rustys offroad stainless steel brake lines (red)
-Cardone power steering pump #20-37776
-Acdelco waterpump #252-191
-Rocky road: drop brackets, fixed lower arms(rubber bushings), upper arms (adjustable rubber bushings), bar pin eliminators for shock mounts
-Tomken machine gastank skidplate
-Stinkyfab transfer case bracket with soft durometer poly bushings
-Bulletproof poly engine mounts with soft durometer poly stinkyfab bushings
-BFG 32” Mud Terrain T/A KM2 lt265/75 r16
-Dodge durango power steering box remanufactured(forget the brand but at the time it was the only company doing quality work, was $300+)
-JCR offroad unibody tie in kit with power steering brace
Attachments
Last edited:
