FLAT Poly Water Tank for Underside of Trailer

B

bluebruin

Adventurer
I am revamping my M416 trailer. I want to put a belly skid plate on it and a water tank in the void between the bottom of my tub and the bottom of my frame (this is at most a 4" tall space). I have seen a few poly tanks on plastic-mart.com but they are really expensive for the size.... and most are too tall.

Does anybody know of a US source for a tank like this: (all the ones I see are sold in Australia)

575_1.jpg

http://aussiervproducts.ezimerchant.biz/prod78.htm

If not, I am thinking of using a snake of 3" or 4" PVC pipe capped on one end, and with a fill/drain valve on the other. I have done some research and it appears most PVC is approved for potable water. I would only be filling and storing water at the start of each weekend trip, not long term, so I am not terribly concerned about chemical contamination of my water (no more than any of the cheap plastic most water cans are made of anyway).
 
B

bluebruin

Adventurer
NotAMog said:
Try Ronco Plastics. They carry a wide variety of tank shapes and sizes -

http://www.ronco-plastics.com/
Click to expand...


thank you for the suggestion. they have a lot of tanks a lot closer in dimensions to what I was thinking. thinnest I see however is 5" and its $260 plus shipping. Man these tanks are all just so expensive. I'm going to price out doing pipe I think. I'd really like a belly tank, sure would be nice to keep my center of gravity down since I am now adding a rooftop tent.
 
X

Xterabl

Adventurer
Yeah, just do a bunch of 3" or 4" abs pipe lengths in a manifold configuration. Probably <$75 and about 50% of the volume of the high-priced tanks.
 
B

bluebruin

Adventurer
Xterabl said:
Also, this is probably your cheapest "off the shelf" option:
http://www.plastic-mart.com/product/324/10-gallon-rectangle-poly-tank-rb323
Click to expand...

I must have missed that one. That's a decent price, but still a bit pricey, especially once you add in shipping. Yeah, I was thinking of a manifold/radiator type configuration with the pipe. Does anybody know if a vent is necessary? I see some holding tanks have them.... I suppose you need a way to displace the air in the tank when filling and vice versa when emptying.
 
Mike S

Mike S

Sponsor - AutoHomeUSA
I had a 40 gallon 3/8" welded poly FW tank under the floor of my trailer & protected by a 1/8" steel skid plate. Mounted an on-demand pump in the tongue box and routed the hose to an exterior spigot. Worked like a champ. The tank was pretty pricey.

I have a similar tank on a Bed Slide in the back of my F350 - drinking and dog water. Both were worth the money.
 
B

bluebruin

Adventurer
Mike S said:
I had a 40 gallon 3/8" welded poly FW tank under the floor of my trailer & protected by a 1/8" steel skid plate. Mounted an on-demand pump in the tongue box and routed the hose to an exterior spigot. Worked like a champ. The tank was pretty pricey.

I have a similar tank on a Bed Slide in the back of my F350 - drinking and dog water. Both were worth the money.
Click to expand...


can you share where you got these tanks? thanks
 
B

bluebruin

Adventurer
I crawled under the trailer out in the snow... due to the "V" shaped tie-backs coming from the tongue which extend all the way back to the frame cross member in about 16" in front of the axle, I have limited space to put a tank. I have about a 16x38" space to put a tank which would sit along the axle and forward 16". Its only 3.25" deep from bottom of the tub to the bottom of frame. I don't think my old leaf spring suspension articulates all that much, so I could probably get away with a 5-6" tank and then skid plate. Depends how much weight my tent will add.

A 3" PVC pipe is 3.5" OD, and with fittings to make a manifold shape, I could only get about 3 runs in there. So, that's only about 1 cubic foot of water, or 7 gallons. Not fantastic. But, that's the same as a 7 gal tank on plastic-mart that goes for $120. Its 24 1/4"L x 12 1/2"W x 5 3/4"H

If I go to 4" pipe, I get more like 12 gallons.

what about a skid plate and a flexible bladder above it? Anybody try that?
 
Mike S

Mike S

Sponsor - AutoHomeUSA
bluebruin said:
can you share where you got these tanks? thanks
Click to expand...

The one I use on my truck is this one: http://www.watertanks.com/products/0260-438.asp - 35 gallons - thought it was 40 when I made my original post.

The other was custom made by a manufacturer in Hollister, CA to fit exactly in the space between the frames and to the rear of the axle in my OR trailer. I no longer have the name and address of the company, but they specialize in RV equipment and make poly tanks to order - whatever you want.
 
B

bluebruin

Adventurer
Mike S said:
Thoses are black water totes to drain the sewage holding tanks of RVs. You might check to see if they are rated for potable water :Wow1:
Click to expand...

don't know if they are "rated" for it, but they are polyethylene..same stuff the water tanks are made of.... I'm still thinking of going the PVC pipe route.
 
Mike S

Mike S

Sponsor - AutoHomeUSA
There are several types of poly - one is designed for use with potable water. Ditto for PVC.
 
You must log in or register to reply here.

Forum statistics

Threads
188,471
Messages
2,905,523
Members
230,428
Latest member
jacob_lashell

Members online

Total: 850 (members: 7, guests: 843)
Top