FRP Flippac For Sale Price Drop!

[Roaming Robertsons]

SALE PENDING

The rig didn't sell so I'm parting out the pieces. For sale is an FRP Flippac. Its on my Nissan Titan which has a crew cab and 5'5" short bed. Flippac makes certain sized campers to fit multiple trucks and I don't know what other trucks this will fit but I would guess it would fit all fullsize crew cabs pickups with the extra short bed. Please do your research to be sure it will fit your truck.

The mattress died a few years ago so currently there is none. We use our old backpacking sleeping pads. You're welcome to those if you want them, or a piece of foam you can glue in should run you less than $100. The awning has sold separately so please ignore any pictures with it on or open. I added interior LED lights (white in one and red/white with two 12v outlets in the other). I also added exterior LED lights to both sides that illuminate in reverse and via a switch mounted to the rear lift window frame.

The rainfly is available separately as well and is listed in a separate auction, make and offer for both. This item is listed on multiple forums.

LED Backup/porch light (one of two)

Interior LED (red/white) light with dual 12v outlets

 

[CallMeCesar]

Hi if this fits a four door Tacoma 05 short bed 5 ft. I'm very interested. Thank you. I'm in Rancho Cucamonga

Sent from my SCH-I535 using Tapatalk

 

[Roaming Robertsons]

Ok, let me take some measurements. We could also ask FRP or just meet up and try.

 

[Roaming Robertsons]

Flippac measurements:

Interior depth (front wall to rear wall): 66"
Interior width (sidewall to sidewall): 72"
(it hangs over the side of the bed several inches)
Width between bolts (side to side): 64"
Exterior height to roof overhang: 23"

 

[CallMeCesar]

Ok sounds good I think it might be a little too big for my truck. I'll verify in the morning

Sent from my SCH-I535 using Tapatalk

 

[Cummins_expo]

If this only fit the Dodge.....

 

[Roaming Robertsons]

Price drop to $1800, OBO.

(Don't know how to change the thread title!)

 

[billy bee]

(Don't know how to change the thread title!)

A moderator can change it for you...

I am shocked this hasn't sold. The used FlipPac market is practically non-existent. If I were in the market today, I might start thinking differently about my approach to buying. The most difficult piece is finding a FlipPac...ANY FlipPac. When one comes on the market, I'd buy it. Or at least find one that fits a truck I might be OK owning. Then go out and find a good truck. So, I wonder what else this FP will fit???

bb

 

[billy bee]

Flippac measurements:

Interior depth (front wall to rear wall): 66"
Interior width (sidewall to sidewall): 72"
(it hangs over the side of the bed several inches)
Width between bolts (side to side): 64"
Exterior height to roof overhang: 23"

This pick-up truck bed size chart might help potential buyers find a fit for this beauty...

http://www.truckinamerica.com/toppers/BedSize.htm

It shows the bed size of the Titan as:
SB--Titan (Quad Cab) 04-07 L68 3/4" W70 3/4"-69"

Other trucks it might fit:
SB--Crew Max Tundra (5.5' Box) 07-11 L67" W71 1/4"-69"
5.5--F150 Super Crew 04-08 L68 1/2" W71 3/4"-68 1/2"
5.5--Lincoln Mark LTÂ 05-08 L68 1/2" W71 3/4"-68 1/2"
5.5 F150 EC (Super Cab) 04-08 L68 1/2" W71 3/4"-68 1/2"
5.7 Dodge CC (09 2500 & 3500= 08 Body) 09-11 L68 1/4" W72 3/4"-68"

Here is another chart that confirms the 04-05 F150 Supercrew might also fit:

Bill

 

[Roaming Robertsons]

Thanks for the charts Bill. As the charts confirm, I suspect it will fit any of the full size pickups with the double cab and the extra short bed.

 

[Roaming Robertsons]

Final price drop to blow this out so I can move on, $1600.

 

[Camelfilter]

...Ugh! Too far away!...Any interest in meeting up halfway, say around Denver CO...(LOL!).

I'd actually been thinking about calling up shops around you to see about getting your bumpers & flippac uninstalled from your T & then shipped to Boston for my T. Likely shops around my end wouldn't install the bumpers, but might the FP. Shipping & labor would likely kill the deal, but haven't spent my due diligence yet...

 

[Roaming Robertsons]

...Ugh! Too far away!...Any interest in meeting up halfway, say around Denver CO...(LOL!).

I'd actually been thinking about calling up shops around you to see about getting your bumpers & flippac uninstalled from your T & then shipped to Boston for my T. Likely shops around my end wouldn't install the bumpers, but might the FP. Shipping & labor would likely kill the deal, but haven't spent my due diligence yet...

Actually, I need to go to Greeley soon to see my niece's new baby and pick up a large sign. For the right price, I could put the Flippac and bumpers on my flatbed Dodge and meet you in Colorado somewhere. My brother-in-law may just help us do the bumper swap in his shop in Greeley. PM me if you're serious about this option.

 

[SilverBullet]

If you have a5.5' beef I am out of luck. Tac return is coming and I would love one, but my 06 SD has a 6.5' bed. Good luck.

 

[Camelfilter]

Heck yeah! That would be great! (PM'd contact info)

I'd be looking at ~$1000 in gas, so that would surely be less than having them removed & shipped from California. It's ~30 hours drive one way, which is do-able for me.

Timing would be the issue I'd imagine, I work 8 nights on 6 nights off, so could make it to Greeley twice per month. Likely on a Saturday, perhaps a late Friday (I'd be pretty wiped from the drive, so not much help on install.).

My Titan is a white 2013 Pro-4X Crew Cab.

I'm not sure wether the front OL bumper will be a direct fit, but if your brother-in-law has a shop they could likely make something work.

The rear from what I understand should be direct fit, but again a shop might have to fiddle. If the shop can make them fit (with ease, without a several days wait), then you could have my OEM bumpers. Might help offset costs?

If your brother-in-laws shop couldn't make the OL's fit (without a couple days delay), then I'd have to keep my OEM bumpers & carry the OL's back in my bed.

My rear bumper has the sonar sensors, and I would like to keep them. I'd like to see if I can modify the offroad bumper to accept the sensors (I'd be happy to do that back at home).