Lets see some full size pictures...

[RedM101A2]

My 2002 GMC 2500HD 6.0 and 1990 M101A2 and converted canoe hauler.
They have both been fun toys.

 

[NorthernWoodsman]

How? Did you shorten the frame?

View attachment 451858View attachment 451860

 

[Mundo4x4Casa]

Layover in OR after camping on the center line of the total eclipse of the sun in eastern OR. Rumor had it that fuel would be scarce so I loaded 3 cans on the rack. Never used any of them. jefe

 

[CoronaKJ]

Not necessarily roughing it but had great time away from the heat traveling the central coast on south stopping into pismo for a day along the way.

 

[Mundo4x4Casa]

Two frames back I posted a pic of our docilemobile. Here is some action on a fairly actionless thread going up the Diablo Dropoff in Anza, a 300 foot blow sand hill with moguls near the top carved by folks without lockers. My bro John, JR, filmed most of the action. Some particulars:
35 inch, 315x75R16 AT-3 tires with tire pressure reduced to the minimum for a 10K pound rig: 20 pounds. Rear wheels are Stockton Wheel 'Power Wagon' 10 inch wide steel wheels where most of the weight resides going up hill.
1st vid is a short but steep section, off camber with moguls to get to the base of the drop off. R front tire tried to lift: low range, 2nd gear.
https://www.dropbox.com/s/xg1lwe92448ry7z/Mogols at great sand hill Anza.m4v?dl=0
The selection of gears was important. 6 speed manual trans in 4th gear low range to start dropping to 2nd gear for the moguls. Open my dropbox files for these short vids. jefe
https://www.dropbox.com/s/bfj5y93wsd7vfkw/jefe does sand hill at dry wash of the devil Anza.m4v?dl=0

 

[AnarchyintheAK]

My kryptoniteView attachment 458284

Love it! It's just recently occurred to me what a smart idea it is to pair a slide in with a service body...I'll probably get the same truck, too, just ten to twenty years older!

 

[fnoff]

How? Did you shorten the frame?

Yep. 16" out behind the cab. Step cut it, welded it, fish plated it, then boxed it where it was cut. The one picture the wheel looks uncenter but I think it's just because of the angle it's spot on under the fender.

 

[XJLI]

Pretend-overlanding

 

[TNSG]

Pretend-overlanding

But its outside!

Sent from my SM-G935V using Tapatalk

 

[Chevrolado]

Pretend-overlanding

I have that same grill.. Love that thing.
Your truck looks good. Looks like a nice day to be outside relaxing and tailgating.

 

[XJLI]

I have that same grill.. Love that thing.
Your truck looks good. Looks like a nice day to be outside relaxing and tailgating.

It is awesome, but I wish it wasn't still so bulky when it folded up. I might have to might legs for it one day. The humidity finally broke here after 2 weeks of 80-90F and 90% humidity, it's great.

 

[gas4blood]

My recently purchased 1994 Blazer. Lots of potential here.

 

[NorthernWoodsman]

Well, that thing looks awesome. I love RCSB trucks and have long dreamed of a RCSB F250/F350. Well done!

Yep. 16" out behind the cab. Step cut it, welded it, fish plated it, then boxed it where it was cut. The one picture the wheel looks uncenter but I think it's just because of the angle it's spot on under the fender.

 

[ChinaLakePW]

Heading into the Rademachers for sunset.

 

[Regcabguy]

My recently purchased 1994 Blazer. Lots of potential here. View attachment 461420

An owner in my neighborhood did a straight axle conversion On a 2-door like yours.
The short wheelbase should conquer Home Depots spaces.