Search results

So I built an AR. My bolt is an ares. When my bolt is in my gun, the gun will fire but is extremely tight when trying to mate/unmate it with the barrel and will not extract or eject the casing. Used my friends PMS BCG and it still had the same symptoms except now it mated with the barrel the...

I assume you're not wanting to build one? If you're willing to wait a little bit you could always buy a complete upper/lower on sale or the specific one you want and get a better overall gun for the same price. A bunch of parts are sourced for the same company so essentially the parts are the...

A tie rod when going wheeling anywhere It will be in more danger.

I essentially did the same thing as rusty. I used roofing gutter repair type of tape and then threw a jc Whitney plastic flooring over it on my 89 runner. Seemed decent but definitely was super quiet. I think the noise is a part of owning an older vehicle. I never got the chance but figured if...

I wouldn't have multiple things running for all night. The heater on and off. lights probably only on when trucks on. Maybe lights in the bed/bed outlet. And potentially a fridge. So I'll look in to those low voltage disconnects.

If you still need this I can get you the info after work.

Has 228xxx on it, and at 6k from a dealership with tax and title. But this one did book on kbb for 5400ish so it wasn't bad according to that. It was steep but I'm selling my wrangler project so I said I'll deal with it since I couldn't find a clean t100 around. Only plan really is to have fun...

short backstory. For me or others that have no experience in navigation accessories other than basic gps that is used on the road around the city and on road trips. Where can we learn what would make our remote treks more enjoyable. ie gps like the montana, montana along with a computer program...

haha, I think my friend just wanted in on the action and showcase his inner hood rat.

Thanks guys! This is my first camper shell. It has the clamps holding it on. Should I look into actually mounting it to the bed or can I rely on those?

Just picked it up earlier. Super clean. 5 speed 4wd 228xxx on the 3.4 with the timing belt just done. Super stoked to take it out for the first time on Halloween. Only plans right now are a new head unit, cb, and dual battery. After doing some more research I might get a mount of some sort for a...

So I left you guys hanging. I sold it to my friend for what was a very reasonable price. I bought a yj because i was talked into by a jeep buddy. Huge misatke for me. I'm going to look at a 2nd gen tomorrow and probably get my front bumper back.

Not really extra. I figured either roll bar would provide adequate protection and I don't wheel hard. But Obviously i do want to be protected. I'm just looking into a new top but would prefer to get a frameless top.

So one of my next projects is to do the family roll bar conversion that way I can use a frameless soft top. So my question is I assume that the only new parts I'll need will be the windshield "retaining bar" that goes above the windshield and the pieces that go behind the doors to seal when the...

I had a 1st gen 3.0 and might pick up a 2nd gen 3.0 today. The 3.0 isn't the most reliable toyota's built and definitely has issues, but I believe the unreliability of the 3.0 is MUCH overstated. If you can get the HG replaced on a rig if it still has the factory one somehow then that should...

Yes it came with the engine harness. but he cut it at, im guess were it meets the dash harness. I actually have a job in wiring but not sure I want to bring home the work yet. I have no emission standards that i need to worry about.

I've been considering it. The owner at NW trail said he can send me a pair of of mounts if i want to make a rear. So I am thinking about it. But I've also been toying with the idea of just a rear bumper of some kind and then use a tire swing from potentially a 2nd gen 4runner or something...

NW Trail innovations bumper and side marker + blinkers!!!!! Truck started like this Then we welded while it was on truck to make sure it aligned properly unlike the instructions. We took it off to finish welding since we only Tack welded and then to grind and paint it...

I have a question and any help from someone would be appreciated! I bought this 99 3.4 but it didn't come with a harness or ECU. Am I correct in assuming that since I only have the engine and they're all the same that I could use any 3.4 mt 4x4 Ecu, be it tacoma or 4runner? Or for some reason...