Recent content by Theshwed

Thanks, exactly what I was hoping for. I didn't want to start grinding away if it wasn't going to help. I will take a look for the Weldtec video.

Hi All, We recently picked up a low mileage 2021 Express passenger, 6.6 gasser, long wheelbase to use as the starting point for our new van build. We just got it back from Advanced for the 4x conversion with a 3" lift. My question is, what are people have to do to fit 285/70-17? Based on...

Hi All - This question is for anyone running big brakes on their Econoline 4x4 conversion. I have an '02 Quigley E350 V10. It has the it has a D60 axle with the GM K30 calipers on the front. I am about to convert this over to either a GM 2500 pickup (circa ~2005 dual piston) or a 2009+ Ram...

Hey Guys, Can anyone recommend a shop in/near Bend Oregon? My 2002 Triton V10 just spit a plug. Bend was the nearest city so we turned up the stereo and made our way there. I have thebhelicoil kit, just need the tools and preferably the hands to do it. Thanks, Paul

I don't have any pictures of anything special. I intend to build my own but I haven't made the time to do it yet. My plan is to build a dual swing out for the van. One side will be a tire carrier to replace the Aluminess. I have been less than happy with that. The other side will be a swing...

@willywalderbeast Was that down on Hurricane Rim /Gooseberry? Looks familiar and in a similar situation!

Got a CCV top put on back in early Feb. Finally starting to melt out of the snow cocoon enough to get some photos. Now it's time to start the interior rebuild!

Just updating this with results if anyone is searching for something similar. The Yeti Lithium 12V regulated was the ticket. Plugged it in and the Dometic fired right up. The Yeti is now powering my CFX50, Propex HS2211, Propane alarm, and water pump. The price is a bit steep, but overall I...

Thanks Gravity. Member PeteRissler mentioned this in a cross post I had as well. It should be here on Friday. Hopefully this clears it up. I measured voltage into the outlet receiver and it was between 10.8 and 11.4. So, yeah, a little low.

Good call. I rarely scroll that far and forgot that section even existed!

Hey all - anyone have experience powering a fridge cooler with a Goal Zero Yeti? I have the CFX50 and I am attempting to run it off the GZ Yeti 1400 Lithium. I am using the power pole connectors with about 12 feet of 10awg run to a cigarette outlet and am plugging in the 12v CFX cable to that...

Hey all - anyone have experience powering a fridge cooler with a Goal Zero Yeti? I have the CFX50 and I am attempting to run it off the GZ Yeti 1400 Lithium. I am using the power pole connectors with about 12 feet of 10awg run to a cigarette outlet and am plugging in the 12v CFX cable to that...

Thanks for all the responses. With my career, I have access to and knowledge of Solidworks and CREO (and a CNC shop). I don't think much CNC work will be needed, as this will be a KISS build. I was just looking for the path of least resistance and avoiding the cold temps outside. Maybe I'll...

Hey All - Has anyone used a CAD program like vanspace3d.com or something similar. I am wondering if it is accurate enough to justify the investment (yes, its minimal, but its the point). I Just got my CCV top installed so I get the pleasure of remodeling the van's interior. If I can avoid...

Typically I leave everything EXCEPT electrical. At a minimum, I usually pull the main supply wire from the house batteries to the distribution block. For some reason I am uncomfortable with selling a vehicle with heavily modified/added battery and electrical systems. In 300k+ miles of van...