Search results

Hey Nathan, Yes I remember you. I still use that picture we took at hungry valley. Hope you get a vehicle soon..... :)

Jim. I have all my fab equipment back from AZ I'm now in yorba linda CA. garage/shop is set up again. Give me a call if you need some work done my rate is less than what he charged you...... Thomas 805-428-3278

So I dont know about anyone else but I dislike the carb can spouts on fuel cans. So here is a modification that can be done in 5 min. NOTE; Disclaimer If you do the modification your spout will no longer be carb compliant and you cannot put the pieces back in. I take no responsibility if you...

this folding/bed bench seat can be mounted in any brand of van. It bolts through the floor, I've had it in two different vans. One was mounted left to right and the other was front to rear like you see here. It is dark blue in color good condition, I have no idea what brand it is, the seat belts...

Does your tailgate stay on when you have the camper on ? hard to tell in the very last photo you posted. Very nice rig I have an FJ cruiser and the wife has a 2006 F250 we are thinking of setting her truck up like yours.

I made mine back in 08 what I did different was make the case split in the middle that way you can get small maps out. They tend to open up inside and some get stubborn to come out, so the split case works great.

That is such an unsafe trailer I cant even believe it. That axle is way to far forward. That thing would be a nightmare to pull.... fishtail city. Other than that it looks nice.

weeelllllllll...... it's actually grip tape for skateboards. Any skate shop and possibly bike shops will carry it. Just so you know make sure you put it on straight the first time because it is a ******** to try and get off. Home depot used to carry something similar but it wasn't as wide. I think...

the color is dark taupe

Graphics/paint on the sides will be the last to go on as I have to install a side door and two windows. I'm also installing a recessed propane tank in the side as well.

I painted the roof tan.... the silver was like a mirror with the sun. installed some fender protection as well, trying to keep the rock dings at a minimum. until I can get some new rims and tires I just painted the rims black.

Cole.... I'm assuming your one dog has some or a lot of wolf in it ?

did they figure out why the roll pin was being pushed out in the first place? I know someone who welded a little washer over the pin and the pin still started pushing the washer up. That seems to be a lot of force on that roll pin..... just curious

So by the looks of the outline on the glass the bird obviously did a face plant on your window AND spit up when he hit it. Nice shot although the bird is probably feeling a little bummed. My guess is a humming bird, they are notorious window crashers.

@wxman... post #1414 in this section. and here are two more.

Wxman..... is your dog a Border collie or a McNab....... I have a McNab and he looks just like yours except mines tail is docked.

I run 265/75/16 on my 01 E350 no lift and dont rub . I would imagine if you have a 2" lift you could go 1 size bigger.

today I rewired the rear door lights, they were wired at the bottom from the factory so I had to re route the wires to the top since I made the door hinge at the top. I also added a utility light in the door on the inside.

So today I welded on some new spring perches and moved the axle to below the springs. With the stock cheesey 13" tires I have 20" of ground clearance on the trailer and 10" for the axle. When I get my new tires that will bump up to 24" on the trailer and 14" on the axle. Here is a before and...

So being that I have several of the stainless steel grab bars, I put one on the top of the tongue as a handle when moving the trailer around. It was much easier to maneuver the trailer with it.