Search results

RipperJ. Call Hemet RV and make sure the "Mesa" is north /South pattern or length wise. This is the lines on the metal. I hope you order 14 Ft long with 1" mesa length wise and "s" lock both sides length wise. and what Color. Just FYI=brian

F/P support arm repair parts I broke the end of my F/P bed support arm, went to (West Marine boat supplies) and found these. see pic, they are available in metal also. FYI brian

space out light from M416 body I found the light housing on the M416 rubs on the tub body, I spaced mine out 1/2" with nuts between the bracket and frame. See pic

Kevin. just insert screw-driver between the red lens & white body and prior off . and you are all set. brian

4" round 18 LED's found red LED lights with 18LED;s on EBay -=eBay item number:131082362878 just FYI=brian comes with NO wiring harness

Purchased from EBay seller "24hourskymall" Also check eBay item number:370872743860. And Amazon has them also=AutoSmart KL-25108RK 4" Round LED Stop/Turn/Tail Light Kit with Red Lens

4" round 12 LED lights I used 4" round 12 LEDlight from EBay $10.00 each,= Pop the red lens off . (BTW) the more LED's in the light the better. remove all the stock light brackets from inside the trailer light, leave 5" of wire to connect to the new LED's. Dremal Grind about 1/4" of the...

I needed to upgrade the rear lights, LED was the only way. see pics

move question best to move your question to Forum="Pop Top truck campers". brian

hood vents There are some companies that make fiberglass hood with louvers. I installed a fiberglass hood with louvers on my Ford Ranger see pics. just FYI=brian

Opional bunk bed Idea. Check out Flip-Pac bunk bed=simple to copy and light weight. also easy to store... from A/T Trailer site of flip-pac camper= "There is also a collapsible canvas bunk bed (180 lbs. max.) that can be used for an additional sleeping place or as a gear sling" Just FYI=brian

rear jacks location Why did you not remove and remount the rear jack brackets facing the rear? instead of the side. No need for jack extensions on the back. As long as you don't back-up into the jack. just FYI=brian

strip/sand blast, paint. keep it stock, this will be my trunk behind my pop-up camper, I just take to much camping. thank=brian

Mark That Jeep Liberty must have super rear springs. Looks like the Trailer hitch is on the ground. LoL brian

Picked up M416 in Northern Calif, Only car I had to tow it home (416 miles) was my sub-compact Madza 2. Towed great at 65MPH and 30 MPG with old military tires. Started my clean-up or rebuild. brian

jack lift help?? ( Tripod jacks won't work because the underwing depth is not deep enough for the mounting base) So why not make some Temp extension under the camper side so you can use the tripod jack?? nice buy, does the rear door opens into the camper?? nice and narrow unit. brian

over weight ?? On your tire it give maximum weight for that tire, now time 4 should give you the maximum weight load. you could rent a trailer if you have over-load in the camper. just FYI=brian

If you have HECO wind-up roof. You may start or have pin holes or wear thru in the inside corners of the canvas roof liner. I noted the Hex bolts may rub on the roof liner when in the Down position. (See Pic). I ordered 9/16” Hex plastic caps from Pro-Dec.com, they sell other sizes also, about...

roof & bar alignment In your first picture you can see the upper bar is not Parallel to the lower bars. I would check the front lift bar see if it bent a liitle. And nothing on the bed??? FYI=brian

roof problem. Maybe its the left side of the roof closing too soon?? I would disconnect all the Heco bars on the roof, and lower the roof onto the camper body. Check where the Heco arms are now, if they are not in the correct attachment position to the roof. this should give you what the...