Search results

Just finished the drawer setup and tested it at the redwoods!

Where did you get the topographical overlay? Awesome setup btw

Luckily I have a half inch underneath because I'm using polyethylene for drawer slides. Thanks for the response!

I'm trying to run a retractable cable to my 60" drawer in my sleeping platform/drawer system. I just need a few small things like 12v sockets and some small led lights for the my pullout kitchen drawer. I bought a drag chain but I'm looking for a more elegant solution.

2018 Tundra SR5 Forestry Truck My new 2018 SR5 double cab with the bench seats and the 5.7. So far a used set of 275/65r18 Duratracs and matching spare, CB radio and phone/gps mounts by hondo garage http://www.hondogarage.com/index.php/product/landing/un-holey-dash-mount-tacoma-2016...

So the one I have is functioning fine it just doesn't work with my android phone during "fast charge" mode. Not enough amps. So I ordered the blue sea fast charge usb outlet that outputs 4.8 amps. That should do the trick! Thank you all for your help.

The worst part is it says "OUTPUT DC 5V 2.1A" right on it.

I just read some reviews on Amazon and other people with android phones and their blue sea usb outlets are having the same issue. They say that you can open it up and short some wires to trick it in to full power mode but I think that's just lame! I was expecting a lot more from blue sea... I...

My problem is my phone isn't charging off my blue sea usb outlet purchased from Amazon. My phone charges fine in the cab of my truck with the usb cable I'm using. This weekend I ran a 10ga wire and fuse to the bed of my truck to a blue sea fuse panel. A 10ga wire is grounded to a stock location...

Thanks for all the help guys. I rarely need to jump start my truck but I work in remote areas and have to be self reliant. I basically overland for my job as a Timber Cruiser. I put on about 30,000 miles a year. It's these nit picky details that keep me up at night. I'll post up when it's all...

Maybe I should go with a slightly higher amp fuse and keep the breakers the same since I can just reset them. I was also thinking of installing a high amp switch to bypass the solenoid all together. The only reason I'm using a fuse is the limited space under the hood.

I'm in the final stages of design and parts accumulation for my dual battery setup. My isolator/solenoid is a cole hersee 200a smart solenoid. I bought a 200a circuit breaker for the aux side and a 200a fuse for the starting battery side. My questions is if I attempt to link the batteries to...

What took me the longest was sanding painting and finish work. My setup is fairly simple and it took me 4 days. I had the lumber store do all the big cuts that had to be square. It cost me about $700 and I didn't buy drawer slides I used hdpe. At the end of the day if I paid myself for labor it...

http://www.expeditionportal.com/forum/threads/9034-Post-up-your-drawer-storage-system?p=1858989

I installed l-tracks in the bed of my truck and secured it with some hardware. My link explains how. http://www.expeditionportal.com/forum/threads/143484-Ranger-FX4-level2-single-drawer-sleeping-platform

http://www.expeditionportal.com/forum/threads/143484-Ranger-FX4-level2-single-drawer-sleeping-platform

I used 4" strip of hdpe on the bottom of my 4' drawer and a Southco latch. There is enough friction it keep it from sliding out on a slope. I work in the woods and it has been bouncing around for the last 6 months or so with zero issues.

Ok mine is a water Jug

I looked at the bottom of mine. It looks exactly like that. LCI brand from amazon.

RUN THE JEWELS! Great work my friend!