Search results

I don't know for sure. But you can drill your own holes if the ones in the bracket don't work for you.

We get our AT Aluminum Can Holders back in stock this Monday, earlier than anticipated. The coupon to get these holders at $99.00 instead of the new price of $110.00 will be valid until midnight on Sunday 22nd. The time is now.

Wade, I'll send you the prototype for experimentation and you can let us know your findings. My first thought is that having two arms makes the windscreen much more stable. It would also cut down on grease splatters hitting your fridge.

Yes the screen can be used on either side of the stove.

I'll get the info on the folding table and cutting board on the website today. It's been on my to do list for a while now just don't have enough hours in a day. Once it is on the website and web store I'll post up links.

Thank you for the feedback. It is a prototype so it's open to change. The windshield sides sits down into the stove by a 1/4". It's a tight fit, tight enough that the cross bars of the grill have to be ground down so that it can slip in. The housing could be raised by 1/2" but that leads to some...

We ran long terms test (60+ days) on the Engel 45 and measured the power drawer using a Doc Wattson. The official power consumption on the unit is 0.7 - 2.5 Amps. Our average power consumption over 60 days of 24 hour usage was 1.2 amps per hour. The official power consumption goes from the high...

Bill, makes me sad to read this.

Just held a tape up to it and it sits at 7 ft.

The only thing that will do that is a blocked jet. Propane is a dirty fuel and if a piece of dirt lodges in the jet it will stop the flow of gas. The jets are located behind where the burners attach. Lift out the grill and burners and you'll see them. They are located in front of the controls...

On solid panels our experience has been that most of the big players produce good quality product. What we found differs is the quality of the frames they are put in. The less expensive units have very weak flexible frames that are unsuitable to solid mounts to a vehicle or to be set up like an...

AT has a full video series on air for vehicles. It is very comprehensive and should provide you with answers to all of your questions.

Well the news isn't that bad. The fabric used for the current Nemo tent is made in Australia to AT specifications. So we have access to the fabric as we import it in bulk. We have identified the main issues with the current FlipPac tent and have sketches that address these issues. The next...

Most vehicles do not have isolators to stop the trailer drawing down the vehicle battery. You could put a diode in, we prefer to keep it very simple and tell people to get into the habit of unplugging the trailer from the vehicle if it's going to be sitting for any length of time.

The reason I suggested 10 gauge wire on the trailer side is that it is typical for the vehicle to have 10 gauge wire running to the 7 pin socket. Maybe I should have just said to match the trailer side wire gauge to the vehicle side wire gauge. The only issue we have seen running lighter gauge...

I haven't heard of any for sale right now. The good thing for the seller is that they hold their value and sell quickly. The bad thing for the buyer is they hold their value and sell quickly. Best place to find a use AT is right on this forum. Good luck.

Here is a generic set up for you. How many watts is the 12 volt hair dryer? Most of the 12 volt outlets are rated for 30amps, if the drawer is higher than that you will have to either have a higher grade outlet with thicker gauge wire, or go direct to the battery.

The holders are made from aluminum, which has also had it's increases in price.

The cost of raw materials just went up again, and try as we may we can't hold the cost of our can holders at $99.00. I'm sorry to say the price is going up to $110.00 All of you on Expo who would like to purchase the holders at $99.00 through our online store, you will be able to do so for a...

Matt, as with everything the crimp connectors are good if they are done correctly. To make it all work seamlessly you need a good crimping tool and a good set of wire strippers. The wire needs to be trimmed back so that enough of the wire will be in the crimp zone, and the butt connector needs...