escadventure
Adventurer
Tune M1 for sale - purchased in Oct 2024 - used about 15 nights
Fits 2015-2020 F150 - 6.5’ bed
Located in Silver City NM
Front sliding window
Rear insert window on aluminum awning door
King bed extension
Tune roof alignment straps installed
Tune insulation pack
Asking $20k for everything listed below. This is a savings of thousands dollars and a whole lot of time to build a ready setup like this. Willing to negotiate if some items aren’t wanted.
Doesn’t include diesel heater seen in pics. (Already sold)
This is a great turnkey setup that works well. I don’t use it enough and need to make room in the garage so I’m selling a bunch of stuff.
I’ll meet the buyer at the Tune factory in Denver - 11hr drive for me, if the buyer arranges install.
Equipment included with camper:
- Remote control installed for factory LED lights
- Pull handles installed on front of roof to assist raising and lowering
- Small shelf mounted on LH side near bed
- Pressure vent installed in driver’s side awning door to help mitigate dust intrusion
- Custom made screen for rear entryway includes magnetic split, mounted via velcro
- Vent has a Reflectix insulation cover for inside when heating interior space
- Reflectix covers for front and back windows, installed with velcro
- Extra bulb seal installed at bottom of rear awning door to help mitigate dust and make the
interior space more thermally stable
- Step stool mounted under the bed overhang
- “Trasheroo” style overlanding trash bag
- RV hatch door mounted in RH awning door with custom baffle to interface magnetic mount
heater hose and power cable access
- Bed platform has marine carpet mitigate condensation
- Two 4” mattresses with memory foam, removable flannel cover with rubber bottom. Includes -
two small camp size matching pillows with removable covers - 75”x30” - this leaves room on
each side for storing clothes and extra bedding with the roof down. The 4” mattresses do allow
for blankets and pillows to be left in place with the roof down
- DIY cabinet and base platform that is easily removable in just a few minutes with six screws.
These are built using 2020 aluminum and 1/4” plywood. The cabinet plywood is additionally
laminated with fiberglass sheet for durability. Platform has tie-downs for fridge and battery pack.
Cabinet has a full length top piano hinge door, aircraft seat track in several places (will include a
couple tie-down devices), and an original Lagun Table (not a Chinese knock off) with Acacia
wood table top
- Spun aluminum 2.9 gallon fuel tank, (will work with the Tune propane tank mount) not
installed
- Taruca 180 awning w/Tune quick release mounts
- Joolca ensuite single shower w/Tune quick release mounts
- Joolca Nomad on demand hot water system w/Dc power adapter
- Bluetti D40 - DC to DC charger mounted on front wall of camper with 60amp inline reset CB.
Connected to vehicle main battery via aviation cannon plug at camper front wall
- SetPower DT45 dual zone 12v fridge w/bluetooth control
- Bluetti AC200max
- 3ea 200 watt portable folding panels
- Power distribution unit w/12v and USB plugs mounted on RH deck
- Chuck box - 3pc Bauer tool boxes w/collapsible sink, Wheatstraw dinnerware set, set of various
kitchen/cooking items, 2 extra Coleman propane cans
- Small tool box modified for use as hygiene kit
- Custom box for propane stove mounted on driver’s side interior
- Stansport stove model 212-50 25kBTUs
- Brackets installed on RH side for storing flat items like table and chairs
- Two Scepter 5gal jerry cans for water storage with spigot
Fits 2015-2020 F150 - 6.5’ bed
Located in Silver City NM
Front sliding window
Rear insert window on aluminum awning door
King bed extension
Tune roof alignment straps installed
Tune insulation pack
Asking $20k for everything listed below. This is a savings of thousands dollars and a whole lot of time to build a ready setup like this. Willing to negotiate if some items aren’t wanted.
Doesn’t include diesel heater seen in pics. (Already sold)
This is a great turnkey setup that works well. I don’t use it enough and need to make room in the garage so I’m selling a bunch of stuff.
I’ll meet the buyer at the Tune factory in Denver - 11hr drive for me, if the buyer arranges install.
Equipment included with camper:
- Remote control installed for factory LED lights
- Pull handles installed on front of roof to assist raising and lowering
- Small shelf mounted on LH side near bed
- Pressure vent installed in driver’s side awning door to help mitigate dust intrusion
- Custom made screen for rear entryway includes magnetic split, mounted via velcro
- Vent has a Reflectix insulation cover for inside when heating interior space
- Reflectix covers for front and back windows, installed with velcro
- Extra bulb seal installed at bottom of rear awning door to help mitigate dust and make the
interior space more thermally stable
- Step stool mounted under the bed overhang
- “Trasheroo” style overlanding trash bag
- RV hatch door mounted in RH awning door with custom baffle to interface magnetic mount
heater hose and power cable access
- Bed platform has marine carpet mitigate condensation
- Two 4” mattresses with memory foam, removable flannel cover with rubber bottom. Includes -
two small camp size matching pillows with removable covers - 75”x30” - this leaves room on
each side for storing clothes and extra bedding with the roof down. The 4” mattresses do allow
for blankets and pillows to be left in place with the roof down
- DIY cabinet and base platform that is easily removable in just a few minutes with six screws.
These are built using 2020 aluminum and 1/4” plywood. The cabinet plywood is additionally
laminated with fiberglass sheet for durability. Platform has tie-downs for fridge and battery pack.
Cabinet has a full length top piano hinge door, aircraft seat track in several places (will include a
couple tie-down devices), and an original Lagun Table (not a Chinese knock off) with Acacia
wood table top
- Spun aluminum 2.9 gallon fuel tank, (will work with the Tune propane tank mount) not
installed
- Taruca 180 awning w/Tune quick release mounts
- Joolca ensuite single shower w/Tune quick release mounts
- Joolca Nomad on demand hot water system w/Dc power adapter
- Bluetti D40 - DC to DC charger mounted on front wall of camper with 60amp inline reset CB.
Connected to vehicle main battery via aviation cannon plug at camper front wall
- SetPower DT45 dual zone 12v fridge w/bluetooth control
- Bluetti AC200max
- 3ea 200 watt portable folding panels
- Power distribution unit w/12v and USB plugs mounted on RH deck
- Chuck box - 3pc Bauer tool boxes w/collapsible sink, Wheatstraw dinnerware set, set of various
kitchen/cooking items, 2 extra Coleman propane cans
- Small tool box modified for use as hygiene kit
- Custom box for propane stove mounted on driver’s side interior
- Stansport stove model 212-50 25kBTUs
- Brackets installed on RH side for storing flat items like table and chairs
- Two Scepter 5gal jerry cans for water storage with spigot
