My son and I are sleeping in the back of our (new to us) 2004 Suburban on our outings. Went to eastern Washington last weekend and it was COLD at night. Looking to augment our sleeping bags with an electric blanket for really cold nights. Additional power needs at this time are pretty minimal; 12v charging of electronics, lights, inverter for blanket (unless we get a 12v one) and laptop, maybe a fridge down the road. I would also like the ability to jump start off the second battery as a backup to the primary.
My plan was to do a KISS install ala the How to make a cheap isolated dual-battery setup for $50 thread. I tried to read all 100 pages, but got lost in some of the details so I am looking for some specific help. I understand that I need to run heavy duty wire from the starter battery hot to the isolator, from the isolator to the house battery hot and between the two negative terminals. I also understand that I need a 12ga wire from the isolator to a fuse that is key on and that I need to put fuses between the two batteries and the isolator.
My questions are:
1) Based on my needs above I am not sure how to size my components. For the isolator/relay, what amperage do I need. Happy to pay a little extra for the 500 amp model (https://www.amazon.com/dp/B001YIPXR2?tag=viglink20599-20) or is that overkill. Would the 200 amp Stinger (https://www.amazon.com/Stinger-SGP32-Battery-Relay-Isolator/dp/B001HBYXVS) be sufficient? Not sure what this is based on; what my alternator puts out or what my expected draw is going to be. Does wanting to jump start myself through the isolator affect this.
2) Based on the size of isolator, how do I size the fuses? Is there an advantage to fuses versus circuit breakers.
3) Also based on the isolator, what size wire do I need? Can I buy cables or do I need to make them myself?
4) I understand that with an isolated setup the batteries do not need to match. I currently have an AGM starting battery. What will give me the most capacity in a 34/78 battery at a reasonable cost? Will a deep cycle lead acid work or should I spend more for another AGM. The battery will be mounted in the factory second battery location under the hood.
5) Once all this is in place, how do I actually tie into it? I am assuming I put another fuse block somewhere then run any needed wires through the firewall and inside?
Sorry for all the questions, but help is greatly appreciated. My head starts spinning when reading through all the detailed electronics information and various options. Maybe it is because I do not drink beer only coffee. :coffeedrink:
My plan was to do a KISS install ala the How to make a cheap isolated dual-battery setup for $50 thread. I tried to read all 100 pages, but got lost in some of the details so I am looking for some specific help. I understand that I need to run heavy duty wire from the starter battery hot to the isolator, from the isolator to the house battery hot and between the two negative terminals. I also understand that I need a 12ga wire from the isolator to a fuse that is key on and that I need to put fuses between the two batteries and the isolator.
My questions are:
1) Based on my needs above I am not sure how to size my components. For the isolator/relay, what amperage do I need. Happy to pay a little extra for the 500 amp model (https://www.amazon.com/dp/B001YIPXR2?tag=viglink20599-20) or is that overkill. Would the 200 amp Stinger (https://www.amazon.com/Stinger-SGP32-Battery-Relay-Isolator/dp/B001HBYXVS) be sufficient? Not sure what this is based on; what my alternator puts out or what my expected draw is going to be. Does wanting to jump start myself through the isolator affect this.
2) Based on the size of isolator, how do I size the fuses? Is there an advantage to fuses versus circuit breakers.
3) Also based on the isolator, what size wire do I need? Can I buy cables or do I need to make them myself?
4) I understand that with an isolated setup the batteries do not need to match. I currently have an AGM starting battery. What will give me the most capacity in a 34/78 battery at a reasonable cost? Will a deep cycle lead acid work or should I spend more for another AGM. The battery will be mounted in the factory second battery location under the hood.
5) Once all this is in place, how do I actually tie into it? I am assuming I put another fuse block somewhere then run any needed wires through the firewall and inside?
Sorry for all the questions, but help is greatly appreciated. My head starts spinning when reading through all the detailed electronics information and various options. Maybe it is because I do not drink beer only coffee. :coffeedrink: