UJOR Build Thread

[Matt.H]

and have a road force balancer in house.

 

[ujoint]

Why does this van look funny?!? A few reasons !!! Big stuff.

This van is from CA and getting our 6" conversion. Not what you see here though. This is a 6" lift with 33" tires and a Stage2 front axle with a Spyntec Hub conversion and different ABS wires to make the RSC/ABS work w/o the Dynatrac RSC upgrade we've been using for years. This axle will be removed and installed into my club wagon project along with these wheels/tires soon.

So, long story short is that we can provide RSC equipped axles quicker and a bit cheaper (if you don't get the SSBC brake upgrade) which will help more guys get our conversion under their van!

Let me know if you have any questions, I'l add updates to the website soon.

 

[CaptainBuilt]

We don't use beads, we use traditional hammer & stick on weights and have a road force balancer in house.

Thanks!

 

[ujoint]

Another Class C ready for Long Island beaches!

 

[ujoint]

Video! Have a good weekend.

 

[Teamoatmealpie]

I saw one of your rigs out on the Blackrock Desert last weekend. Dude from Reno was up with his family, dirt bikes & camping. Silver with I think CCV Pop top. Good stuff.

 

[ujoint]

Cali 5.4 got its new D60 today, trans is out being converted while we do the rear gears.

V4 doing work with a few scrap runs today. These Yokohamas have been nice so far, I dig them.

 

[CaptainBuilt]

I'm calling dibs on a rear bumper.

 

[ujoint]

I'm calling dibs on a rear bumper.

It's coming together nicely, should have the 1st complete bumper ready for pics/etc early next week. Then we'll make another and cost it out for production!

 

[ujoint]

5.4 High top ready to go! video is uploading now. 6" on 35s, Stage 2 front D60 with 4.56 gears, custom spec springs of course, OBA, our FB003 front bumper, Rigid Lights, Aluminess rear tire carrier and an sPOD.

 

[ujoint]

 

[i bike]

I have a favor to ask, next time you guys do a full roof rack install with solar and perimeter lights would you mind posting some pics of the cable routing around the rack and entry points into the van? I got my rack and cable cover strips from you and I'm trying to determine the best way to get all my wiring installed.

Thanks in advance

 

[ujoint]

I have a favor to ask, next time you guys do a full roof rack install with solar and perimeter lights would you mind posting some pics of the cable routing around the rack and entry points into the van? I got my rack and cable cover strips from you and I'm trying to determine the best way to get all my wiring installed.

Thanks in advance

Sure, if you dig I've posted a lot of pics of racks being wired up, here and on FB. We route everything in the channel that we can, everything else we attach via P clamps to the area we'll be going thru the roof.

 

[ujoint]

Dude trip to a friends property for some much needed R&R. My ARB fridge in the Sherpa finally took a crap so I went to VL Vehicle Outfitters and picked up a new Dometic. Super nice piece! Got to shoot a .50 cal (whoa!) and I made a bunch of pizza. Good times.

 

[i bike]

Sure, if you dig I've posted a lot of pics of racks being wired up, here and on FB. We route everything in the channel that we can, everything else we attach via P clamps to the area we'll be going thru the roof.

Thanks Chris, I found a few on the FB page. Do you guys usually leave the plugs on the little rigid light bars or just clip and splice?


Sent from my iPhone using Tapatalk