Search results

After reading many posts on speaker installs for my second gen Monty,I'm still not 100%sure if I can use regular 4 ohm speakers? I've read in a few places that the system requires 2ohm speakers? Can someone set the record straight? Thanks:Wow1:

well I went through the whole exercising thing to loosen things up. The truck shifts into 4h no problem, it( the center diff dash light) just continually flashes when I try putting it into locking center diff and Icant lock the rear diff unless the center diff is locked. So where would I start...

Troubleshooting my fogs but can't locate the fuse? Anyone? Thanks

Well my vehicle needs a catalytic converter. Mine has a hole and is leaking. I'm in ny so everything's prett rusty and it should be fun getting the old one off. My question is ,does anyone know of an aftermarket delete or bypass pipe? Sine the vehicle is OBD I there's no emission test so I feel...

Regretfully selling myvery clean 99% rust free monty for sale. I bought it 10 months ago,did the ball joints,idler arm,pitman arm,bilstein shocks,new IAC valve and 4 new Bridgestone Revos 31X10.5X15. It runs and drives well. It needs the gas tank repaired or replaced,it leaks when the fuel is...

I searched but found nothing. So any the recommendations for driving my LWB Monty in the beach sand. Im running Bridgestone Desert Dueler Revo's(31X12.5) stock height, on bilsteins. Diff settings,tire pressures,etc. Thanks 'Jerry:sombrero:

looking for a good shape fuel tanks for my monty,Im located in Long Island,NY thanks

Need to check the Idle Air Controller on my 1995 SR,I went through the FSM but cant find the correct process? im having a cold start issue. thanks Jerry

I'm slowly going through a 1995 montero sr to get it up to par. What fluids for the diffs,transfer case and tranny are recommended? Thanks

Bought a Monty and went looking for the factory jack but it's not there. Is it worth sourcing an OEM one or what should I get? Pics? Thanks.

Picked up in port Washington,ny or u pay shipping. Complete.

Rebuilding the front end on my 1995 SR and the lower ball joints wont release. I've tried wacking the knuckle ,heating it and wacking the nut on the bolt that comes out of the bottom of the ball joint ,all to no avail. What am I missing? HELP!

My 95 SR is tricky to start when cold. When left sitting overnight starting the truck requires slightly depressing the gas pedal or it immediately stalls. If you manage to hold the rpm (via pedal pressure) and keep it there til it warms up say a minute or 2, then the idle will hold and it will...

Sold

the bushings on the large bars that come off the front of the rear axel and run forward to a bracket on the chassis,have dried and cracked,Im looking to replace them,trying to figure out exactly what they are called? the FSM call them ,"lower arms". While rockauto ,I think,refers to them as...

Anyone know if a 15" x 8" wheel with -18 offset fit my 95 SR? Stock suspension. thanks

light or medium coils,lightly used or new thanks Jerry

Well 2 weeks ago I joined the Mitsu community and picked up a 1995 SR with 158,000 miles. First night I pulled the running boards off ,then put a set of 31 inch tires I has for my Scout 800a on the factory wheels. Next I replaced the rear sway bar endlinks,one was broken. Today I put 4 new...

I located a nice 1991 montero with a bad motor. If I picked it up what motors would swap in without sinking toomuch money? Im partial to desiels.

Replacing the factory shocks on my 95 SR and the shaft keeps turning with the top bolt. So I decide to get the cutting wheel out and proceede to cut through the factory wiring harness that runs down the chassis:wings:! Cut through half the wires,still probablly 8-10 wires. Still didnt get the...