Search results

You'll need to trim the bottom plastic rocker trim. Mine had small plastic extrusion lines on the inside that matched almost perfect for the long straight cut. They're shaped like a T in the pictures. The end cuts are measure twice and cut once affair [emoji6]. Sent from my E6810 using Tapatalk

The top height of the drawers are a few inches below the seat back height. My son's head and body is well inside the car seat and protected from rear impact. We store everything on top inside front runner bags and haven't had an issue with them sliding around much. I've been running the basic...

All design, fabrication, and wiring was done by myself. Any project no matter how big or small should start with detailed planning and research. Aluminium is expensive compared to wood but thinner material yields equal if not greater strength and longevity. Using thinner material creates more...

Anybody else using this inverter? http://www.cooperindustries.com/content/public/en/bussmann/transportation/products/power_conversion/inverters/true-sine-wave-inverter.html I've all ready integrated this into my build but was looking for some long term reviews or experience. Thanks. Sent from...

All aluminum construction with a stainless slide out tray. All my aux rear power components are integrated behind the left side panel. Sent from my E6810 using Tapatalk

I carry a fire axe and hatchet in my series and a Max tool and chainsaw in the LR3. Sent from my E6810 using Tapatalk

Just finished this setup. Sent from my E6810 using Tapatalk

I searched a bit during my build and never found anything I was satisfied with. So I did a 30' cord reel attached to inverter integrated into my drawer system. Sent from my E6810 using Tapatalk

2 plus gallon capacity don't really know. Using air for tires, air tools, and a blow gun to clean up the interior on trips. Sent from my E6810 using Tapatalk

Can we discuss compound systems using 2 blocks to achieve a 4:1system [emoji23] Sent from my E6810 using Tapatalk

Tapped out the odd ball factory fitting on the tank to 3/8npt and used a 3/8npt to jic4 adapter fitting and used all braided stainless jic4 hoses for everything. Sent from my E6810 using Tapatalk

Compressor, solenoids, and fittings are mounted under the truck in spare tire location with a custom bracket with air intakes plumbed inside the truck. The hose reel is integrated into the trim panel of my custom drawer system. Sent from my E6810 using Tapatalk

Seat belt so it's adjustable in height. Sent from my E6810 using Tapatalk

Mounted a factory air tank on the passenger side for aux air storage. Mounted in the same area in between the rocker and frame as the driver's side suspension air tank. Modified and fabricated brackets for mounting. Removed and rethreaded factory air fittings to common 1/4 npt. This tank and air...

Lucky 8 sliders here. The hardware that is supplied is cheap. The rocker panel holes are slotted and enlarged to make fitment easier and required adding some hardened fender washers. The step tubing isn't welded all the way around and allows water inside without a way to drain. They fit nice and...

Another vote for front runner stratchit straps. Also as noted by others I've replaced the attachment hardware with larger stainless snap hooks. Also if you haven't bought cases yet take a look at the pelican air cases, much lighter and still as solid as original. Sent from my E6810 using Tapatalk

Every vehicle has a truck gun. Sig MPX in the LR3 and M1 carbine para in the Series. Sent from my E6810 using Tapatalk

The tripod legs are 6' and the ridge pole is around 9'. All the measurements are dependent on the users size and how you want the hammock to hang. It's important to note that both ends of the hammock attach to the ridge pole to to keep the ridge in compression. If the washers on the ridge are...

Lucky 8 sliders cover everything all the way to the frame. Sent from my E6810 using Tapatalk

Still a work in progress... Sent from my E6810 using Tapatalk