Search results

So I got a bit more done. Lined the bulkhead top and rear. Installed section on either side to divide cab and rear. Added more shelving Had to shorten bed/bench to accommodate ply on bulkhead. Added latch to bed support to keep it in place. Broke the storage box lid that goes between arches at...

Found aero board in a local hardware store 1.2mx0.6m sheet in 12/18/25/60mm thickness. Starting at €1.50 Any chance you have a pic of your roof vent? Is it a rectangle flap sort of arrangement? Was always puzzled about the safari roof's, at first I thought it lifted up, is it just a roof...

The aim of this build was to take a standard van type 110 and convert it into what the Irish Government call a motorhome and there are a few criteria which must be met to reclassify the vehicle into a motor home. "A vehicle of Category M with living accommodation space which contains the...

Yea definitely safer as soon as I had it done I knew that it wouldn't work. The stove can actually slide forward a bit away from the side. The stove in the picture won't be used all that much I will use my Coleman for all except when I need to simmer food because the Coleman doesn't simmer. I...

The compromise I went with to make it look "built-in" but removable. The steel bowl beside it will be the sink. Sent from my HTC One mini using Tapatalk

Yea changed it and the stove is in the same location but instead of just the burner cut out the entire stove has been cut out and raised. Pic's to follow. I will be adding a shelf to the door also for my petrol stove. Sent from my HTC One mini using Tapatalk

So I started on the storage and kitchen end of the build. Not sure if I was right to put the stove in like so. Or have it on top Sent from my HTC One mini using Tapatalk

I have used a bit to fill a hole in the floor and it really does expand a lot. If i was using it I'd do it in stages. Letting it fully expand before squirting in more. Does anyone know where I could get a set of drawings for rear auxiliary tanks? The one behind the left-hand rear wheel Sent...

Never thought that it would push the sides out. Closed cell it is. Sent from my HTC One mini using Tapatalk

Forgot to show the support for the seat/bed and the removable storage that fits between the arches and also supports the bed. Sent from my HTC One mini using Tapatalk

Water will be stored in a Jerry can on the shelving for now and eventually I'll make a tank for the rear right arch. I won't be lining it just yet. Have considered using the closed cell foam or what about putting ply on the walls then filling with a expanding foam? Part of the reason for...

Seeing that I have to baby sit and can't get out to the garage I thought that I would share what I'm using for stove, sink etc. Stove is from halfrods Sink includes a stainless steel mixing bowl i picked up locally, the rest is from ebay...

So didn't get much done with the land rover till this weekend. Here is a picture of the interior when I got it. I ripped out some of the old ply and replaced with new. The added a bed which folds into a bench seat or stores vertically. On the right-hand side I will be installing shelving...

Looking good. Will be starting my project this week and your work is great inspiration! Keep it up. Did you consider the Coleman dual burner petrol stove for your build? and how many litres will the water tank hold? I was thinking of putting a tank either side in mine for fuel and one at the...

Thanks wasp will get reading that thread Sent from my HTC One mini using Tapatalk

Yea I will try find a camper van dealer to have a nosey. I wouldn't say I'm anxious to have it looking original I would just prefer it to look like the next 110. So yea stealth camper 😄 I also do think that the method I have in mind would be fairly easy to construct and not involve much...

I seen a video of someone putting up their maggiolina but can't see how the mechanism works. What fabric to use was gona be my next thought once I've sorted out how to fix it to the 110. Sent from my HTC One mini using Tapatalk

I will draw something up show what I plan to do at the back door. Regarding the front at the windscreen. The strip of metal and the rubber seal should simply follow the edge. The seal and metal is basically inserted in between the roof and sides. I was gona show counter sunk bolts in the diagram...

Here is what I imagine I could do to seal the 110 with roof up and down. I think that this would be fairly waterproof when the roof is lifted and should be near 100% when the roof is lowered. I think that if the fabric sides were removable and could be zipped in or out then I can leave the...

Here is something I just whipped up..ok I lie I seen it and had it saved on the laptop for future reference but I didn't like the idea of lifting the entire roof because i didnt want the fabric sides/front in the driving compartment above my head especially when wet etc. But if i went with this...