Search results

Heres what was removed. Drove it to work today, full turning stop to stop with no interferance or rubbing.

I would like a little more lift in the front, its still not level with the coil boosters. Any coil recommendations?

I trimmed about an inch off the front bumper, and about an inch and a half from back of front fenders. I started right next to the bottom fender bolt and arced up untill it tapered off at the body line. Using some coil spring boosters, half inch 8 lug spacer plates, and the trimming I did it...

Ordered five 285/75 16 tires, an extra baja rim and a spare tire carrier to bolt to rear door. I got some half inch spacers as well. Going to trim/angle the sides of front bumper and cut off a couple inches of the rear of the front fender wells cutting at a sloping angle. Hope the spacers give...

Thanks!...Its just indoor/outdoor carpet from menards. The cheap stuff but used it before on a boat and it held up well so figured it should be fine inside a van.

Have not updated in a while. Got my walls done and need to install the ceiling next. Got my hammock today and did a test run in it. Very comfortable. I found a 10'6" long double nest hammock which is a little longer than a usual sized one. It worked out great! Laying at a diagonal ...your body...

Feeling under the weather but managed to get the driver side insulated and ready for the panels. Spent the whole day pushing insulation up the pillar ribs and in the cieling ribs. Didnt have anymore spray foam so made do with the roll insulation, just took forever.

I picked up some bar and chain oil. Too thick to spray from my pump sprayer but managed to get it in along the inside fender areas. Probably just go with fluid film and a spray gun on the air compressor for the undercarriage

Got backtracked and had to drive out of state last weekend but grabbed some lauan sheets,foamboard,insulation, and carpet last night. Quick question. If i adhere the carpet to the lauan sheet while its laying flat position using indoo/outdoor carpet glue.... how long does it need to dry before...

I was going to use fluid film but have read alot of threads in the past about bar and chain oil working good and its dirt cheap

Got my 02 e350 SD gutted with rigid foam/ plywood/ carpeted floor laid. Getting ready to start on the walls but before I do - I wanted to spray some bar and chain oil into the empty interior voids so it will seep down into the fenders and prevent rusting out. Then im going to spray into the...

Ok...ill pass on the mdf and look for the lauan... Thanks for the tips!

not much progress lately. Need to go get some wall/roof sheets and carpet. Couldnt find 1/4" mdf last time I looked and wood wall panels were too much for my cheap a##. Whats an ideal cheap panel to use for the walls? Will be covering with exterior marine carpet.

No prob.... Got the new rotors and pads installed. Small amount of diff fluid leaking at the outer seals but will work on that later when installing lift. Just put in the new idle pulley and belt tensioner pulley and WOW! Super quiet now.... sounds like a well oiled machine. The 2 chamber...

Nevermind....got rotor off, just had to wig out pulling on it lol.

The 07 vic has egr so sure the 2010 does too. Maybe ill try cleaning it. On the van....I have the pass side brakes and rotor done. On the driver side the rotor wont come off. Its broke free but has springy resistance, its caught on the parking brake pads. Ive pulled and released the brake while...

Parking brake.... dang im stupid lol, didnt even stop to think about it lol, been a while since ive pulled rear rotors. Anyway, the gear lube seems to be concentrated right around the seal, i dont think its bad yet. The old pads were dry. Im going to have to act like I didnt see it leaking for...

Not really too concerned about rims/tires right now untill I figure out what im doing about drum pads and axle leak above but figured id go ahead and post pics of the inside of the mystery rims I have that were in question. I think they are american racing rims but not sure. A quick measurement...

Arggggg....when it rains it pours! My 2010 vic is bucking bad. Put new plugs and coils in and its still doing it. No fault codes or pending codes so no idea now whats going on although im suspecting torque converter. Ny 99 navigators sticker expired And I got this 02 e350 up on stands and...

I think im leaning the same way. Blocks in back... maybe the 4" lift and some 285/75s or still may go with the actionvan 6" and 35s Going to call weldtec when i get time and see what actual prices and self install dificulty will be