Fold down table for rear door?

[ssssnake529]

I'm looking for a panel to replace the stock panel on the inside of the rear door of my 1996 Disco I.

I'd like it to have a drop down table, and preferably be made from aluminum.

Does anyone sell these?

 

[h2os2]

http://www.columbiaoverland.com/web/node/294

 

[ssssnake529]

http://www.columbiaoverland.com/web/node/294

Thanks for the link.

It should be fairly easy to fabricate a table with that panel in place.

$115 for shipping, though? That seems kind of crazy.

 

[Viggen]

No way its that much. I got mine from Justin at Lucky 8. Scrounged the garage for an old butcher block and continuous hinge and was able to build a table that works nicely.

 

[Sirocco]

One you have the Pre-fabed door card in place making the table is easy. There are infinate ways to hang it and lock it but the basics are the actual shelf and either a continous 'piano' hinge or a couple of normal hinges. I have strung mine up in the past by using webing riveted to the door card and shelf but recently I have bike brake inner cable held with clamps (allows for adjustment should it be needed) it is also locked up by a hinge mostly seen on the tailgates of series vehicles (keep it LR!)

HTH

G

 

[benlittle]

No one actually sells a table but they have been made Do a search...

 

[Chazz Layne]

Just a thought: if I had it to do over, I would buy two of the door panels and use the extra for the flip-down shelf (with the big side facing out). I can't remember where I saw it (somewhere on here likely), but it looks perfect for a camp kitchen.

 

[DexGtr]

Just a thought: if I had it to do over, I would buy two of the door panels and use the extra for the flip-down shelf (with the big side facing out). I can't remember where I saw it (somewhere on here likely), but it looks perfect for a camp kitchen.

that is a damn good idea.

 

[benlittle]

This is my table. Couldn't live without it.

kitchen grade stainless panel
1/4-20 riv nuts
1/4-20 stainless button cap screws
1/4 black auto trim x 80in
12.25in 10lb pressure gas struts
stainless strut brackets (boat supply store)
stainless piano hinge
rivets
kitchen grade HDPE cutting board

The nobs have 1/4-20 threads which screw through the table into 1/4-20 riv nuts

 

[AxeAngel]

Got any more pics? Specifically with it down?

Thanks
Sam

 

[ssssnake529]

I think I'm going with this fold up tray/table.

Secure it to the rear panel, and I think I'm done.

http://www.mygaragestore.com/detail.aspx?ID=396

 

[David Harris]

This is my table. Couldn't live without it.

kitchen grade stainless panel
1/4-20 riv nuts
1/4-20 stainless button cap screws
1/4 black auto trim x 80in
12.25in 10lb pressure gas struts
stainless strut brackets (boat supply store)
stainless piano hinge
rivets
kitchen grade HDPE cutting board

The nobs have 1/4-20 threads which screw through the table into 1/4-20 riv nuts

Very nice.

 

[ltngaines]

That is cool. Beer opener, very cool....

 

[brushogger]

Just a thought: if I had it to do over, I would buy two of the door panels and use the extra for the flip-down shelf (with the big side facing out). I can't remember where I saw it (somewhere on here likely), but it looks perfect for a camp kitchen.

that is a damn good idea.

He always has great ideas. I try to steal as many of them as I can! You should check out his roof rack mounting system. Bulletproof!

 

[SeaRubi]

Got any more pics? Specifically with it down?

Thanks
Sam

be ready to be hungry. ben has the corner on food porn around here :sombrero: