Search results

Yes, it would seem they are available: https://aav4x4.com.au/37-wheels-for-isuzu-nps-4x4-up-to-2008/

I'm sure any hairspray would work, it's just a kind of glue. As for rescue tape, I doubt it. I haven't been able to find out what the max boost pressure of the 4HK1 engine is but if it's 15 psi above ambient, with a cross sectional area of the tube of maybe 12 sq inches, you have something like...

$450 - includes new hi-spec clamps and the silicone joiner.

The problem; Isuzu uses a plastic pipe on the output of the NPS's 4HK1 engine's intercooler, presumably because neither a flexible rubber pipe nor a pressed steel pipe as used in the intercooler inlet is conducive to mounting the manifold pressure sensor which is on the low pressure side of the...

I suspect the platform is a separate item.

I've never used a diesel cooktop but I have heard from others who've had them that they have some drawbacks. I have an induction cooktop and it is just terrific. Heating and hot water is from a Webasto hydronic diesel heater. Another drawback to a combo heater/stove would be that it represents...

Could be this one: http://www.circlebusdoor.com/products/electric-triple-retractable-foot-stepebs400/

I know nothing about military tyres, but I can tell you that brand-new out-of-round tyres are a real, albeit rare, thing. It happened to me once, got 4 new tyres, all properly balanced, but experienced terrible steering wheel wobble when driving. They were replaced by the supplier. I've also had...

Taiwan quality is just as good as Japan. I'm old enough to remember when "Made in Japan" meant it was cheap crap, then it was Taiwan, then China - where will the cheap labour be found next? But I was stunned to discover the other day that the Isuzu electric heated wing mirrors are made in...

Ok, so you have inspired/challenged/shamed me into doing better. I've modified the switches so that the diode and resistor in the harness are not required, changed the backlight LED colour to match the stock switches, and dimmed the activation LED (left it blue because I like the...

It looks worse in the image than it does in reality. One problem is that because the NPS has no dash light dimmer, the LEDs are too bright even at 12V (they're basically running at full brightness, which in a more sophisticated vehicle you would never do) so I think I will change the zener...

Wiring diagram and 3d model for the switch adapter attached. I've now added air compressor and diff lock switches to my truck.

Better tell Gladiator Tires that - they specify a load rating of 4300lb for their 37X13.50R17LT. There are several other 17" tyres with published load ratings over 3195lb.

So the switches are the Stedi "tall Toyota" range - https://www.stedi.com.au/rocker-switches/toyota-switches/tall-toyota.html These are push-push switches, not rocker. They are about the right height, slightly narrower than the Isuzu switches. As standard they do not clip into the hole, and...

Well, 5 years later there are still no aftermarket dash switches for the NPS - but with a little ingenuity, I got very close to an OEM look, complete with illumination, and with an extensive choice of labels. And they're relatively cheap. More details to follow.

Australia is not locked down (various states have had varying degrees of lockdown but that's all gone at least for the vaccinated) but there have been and still are some state border closures (or effectively closures due to quarantine requirements.) The border closures are being unwound as...

Custom 2-din mounting bracket for UHF CB, also provides a place to mount the USB ports from the rear of head unit.

Thong holder (no, not that kind of thong - flip-flops or jandals if you prefer.)

Other bits I've done; winch cover - made in two parts because my printer wasn't bit enough to do it in one. It clips onto the top rods of the winch frame and protects the rope from UV.

Well, you need three things; 1. Design software. I use Fusion 360 (free on a startup licence, just requires some hoops to be jumped through each year) or there are other free options like Tinkercad and Sketchup (have not used this lately.) This is what you use to create the 3D model. 2. Slicing...