Search results

Ha bad timing I guess I lifted it up for the pictures, it was tucked behind the terminal, just touching, but not enough to give good amperage when there was a draw.... But yes, good thing it didn't ground out. But I have pretty specifically tried to use non conductive stuff in that area.

Ok checked. 87.7% lowest SOC. temp was 9C or 48.2 F at the battery terminal this is under a little load, but lowest voltage I could find. Thinking about doing an airdog system. I was given some tunes and I think they may be really stretching the stock pump. Thoughts? And now I need...

Good idea, I was really just messing with it. The reason it didn't turn on is they never went below the setpoint on the Tstat (50F IIRC) They are sitting on 1" of foam, and the wall is 1.75" of spray foam, but nothing on the living side. (Footnote: I found the battery issue.... In some of the...

Wow I have not kept up with this thread! Warning, giant wall of update incoming.... Orange is my current thoughts. Spent a week in the truck, its nice. One issue, it seems to be slamming into 1st gear on decel...... Just a real hard shift. Any ideas? Not every time, but its doing it a bit...

Yes split charge. But the more I talk about this the dumber it sounds Sent from my SM-G973U using Tapatalk

No the cells are spot welded. But the tabs between the cell banks are soldered together. Sent from my SM-G973U using Tapatalk

Yes, I was figuring running a separate charger for the lithium, but maybe I am just way over complicating things. I am just a little worried about temps, which is why I went AGM to begin with. 200-300W soldering irons aren't real expensive.... I'll probably just order one.

Just because the AGM will draw down the lithium? I have a PID controller and heat pads in the garage. If I need them..... I need a bigger soldering iron! I cant get these cell banks apart.

Well they are AGM [emoji1787] but yes. Reason is my AGM are new. Work well at cold Temps. Lithium fell into my lap. This bridge is going to make things awkward. Sent from my SM-G973U using Tapatalk

Thanks for the update. This build was a big inspiration of mine. Glad to see its still working well and to most of what you wanted out of it!

I plan on 4s4p pack for 12v nominal ish I don't mind spending $ for good quality, I just don't know where to start with the diy stuff. Thoughts on running both lead and lithium together?

Took a gamble and am dipping my toe into lithium..... Found a 48V 69ah battery on CL that said make offer. Didn't Work. Had proper voltage, but when any load was applied it instantly dropped voltage. So I low balled. Opened it up and there is a ******** stain on the BMS. Cells should be good! 336...

Nice, that's an upper control arm off something :p

Sadly I think 10k for wheels alone puts you well outside most of the current market. Sent from my SM-G973U using Tapatalk

Looking good! Whose wheels are those? Sorry if I missed it.

4.5" OAL, -16 fitting is just under 1.25" ID https://www.cpperformance.com/p-12656-stainless-16-an-steel-bulkhead-fitting.aspx

Yes, but you need to size it for the flow.... Those thank thru Wall fittings are available, also AN style ones are easy for that thickness Sent from my SM-G973U using Tapatalk

Sink in not worried about. Doesn't need a big drain, do you know what shower head your using? 2.5gpm? Sent from my SM-G973U using Tapatalk

Well what size drain are you aiming for? 1.5"? I have some options.... Sent from my SM-G973U using Tapatalk

What diameter are the drains? You should be able to find a stainless bulkhead fitting. Sent from my SM-G973U using Tapatalk