Hodakaguy's 4x4 Sprinter Build

Betarocker

Adventurer
How fast are you driving at night? That's 180km/h across the desert in a trophy truck type output. I just have a pair of LP6 Amber Combos installed while I await the backordered pair of LP9 White Spots. Brightness and range is impressive with just the small lamps.

1609132145956.png
 

Hodakaguy

Adventurer
How fast are you driving at night? That's 180km/h across the desert in a trophy truck type output. I just have a pair of LP6 Amber Combos installed while I await the backordered pair of LP9 White Spots. Brightness and range is impressive with just the small lamps.

View attachment 633652


When traveling late at night across the open spaces of NV you can never have enough light! Plus I'm not gonna lie, I love the looks of them up there :)
Hodakaguy
 

Hodakaguy

Adventurer
Time to finally start posting the TONS of photo's from this summers travels, It's been ages since I've caught the build thread up and with the holidays over it's time to start going through pictures and posting about the numerous road trips that we have taken with the Van this summer.

So I don't clog up the build thread with hundreds of photos I've started another page that I will be posting all of our travel photos and trip reports on. I'll provide the link here and a few teaser pics below....

The current road trip starts on post 11 here: https://advrider.com/f/threads/the-hodakaguy-camping-trip-report-photo-mega-thread.1460644/

And a few teaser photos....

FB_IMG_1609511108527-X2.jpg


FB_IMG_1609511110740-X2.jpg


P8314618-X2.jpg


FB_IMG_1610163459780-X2.jpg


FB_IMG_1610163467775-X2.jpg


FB_IMG_1610163482626-X2.jpg


FB_IMG_1608988289540-X2.jpg


FB_IMG_1608988284878-X2.jpg


P8284006-X2.jpg


Screenshot_2020-09-12%20GPS%20-%20Asset%20Management%20-%20SPOT%20Tracking-X2.jpg


Hodakaguy
 

Hodakaguy

Adventurer
Time to finished off the bed build that I started earlier last summer.

Last summer when I finished the aluminum adjustable bed frames camping season started and I threw some scrap plywood I had onto the frames and secured them with ratchet straps. This setup got us through the summer but with winter here It's time to finish it off before hitting the open road once again.

Here's a shot of the bed frames in the van with the temporary plywood installed.

20210115_105702-X2.jpg



And the bare frames.

20210115_105908-X2.jpg


20210115_110018-X2.jpg


20210115_110156-X2.jpg



With the frames removed I took them into the shop to sketch out the measurements for the top boards.

20210115_130205-X2.jpg


20210115_132245-X2.jpg



With the quick sketch in hand I headed down to the store to snag a couple sheets of 1/2" Baltic Bertch Plywood.

20210115_135740-X2.jpg


20210115_140224-X2.jpg


20210115_141424-X2.jpg



Next stop was to visit my buddy Mike at VanLab, Mike is an up-fitter and has a commercial CNC router that made quick work of cutting out the bed frame tops. Thanks Mike!

Transferring the drawings to cad.

20210115_150943-X2.jpg



Continued Below....
 

Hodakaguy

Adventurer
Continued from above....

And setting up the Router to cut.

20210115_150238-X2.jpg


20210115_151128-X2.jpg


20210115_151141-X2.jpg



And away it goes.......This thing is soooooooo sweet!


20210115_154054-X2.jpg



Mike approves!

20210115_154239-X2.jpg


20210115_154939-X2.jpg



Quick test fit on a frame...yep that should work nicely.

20210115_155154-X2.jpg



While the second frame was being cut we went over all the edges with a router for a nice smooth finish.

20210115_160900-X2.jpg


20210115_161043-X2.jpg



Heading back home

20210115_165815-X2.jpg



Tops sitting on the frames, one extended and one collapsed. The oval sections will provide ventilation to the mattress and prevent moisture/mold from forming.

20210115_180221-X2.jpg


20210115_180229-X2.jpg


20210115_180347-X2.jpg



Now to weld on mounting tabs, drill and counter bore the holes in the tops, seal the tops and assemble everything.

More to come.....

Hodakaguy
 

Hodakaguy

Adventurer
Time to get the tops mounted to the frames. Originally I planned on welding tabs to the frame and using bolts to attach the two, after staring at it a bit in the garage I decided to use aluminum TRIC-nuts instead (Like Rivet Nuts) as they would be faster and cleaner than tabs.

Here I'm getting ready to start installing the TRIC-nut thread inserts.

20210116_100432-X2.jpg



I had a scrap piece of tubing on the bench so I installed one of the TRIC-nuts for a test fit and to show how it functions.

Here's the TRIC-nut.

20210116_095653-X2.jpg



Drilling the hole and installing the TRIC-nut.

20210116_100531-X2.jpg


20210116_100608-X2.jpg


20210116_100621-X2.jpg


20210116_100821-X2.jpg


20210116_100912-X2.jpg


20210116_100917-X2.jpg



Using a standard Rivet Nut Setting tool to compress the TRIC-nut

20210116_101223-X2.jpg



And BAM....instant threads. Threads stayed nice and centered in the hole, perfect.

20210116_101240-X2.jpg


20210116_101304-X2.jpg



Next I clamped the wooden top onto the frame to prepare it for marking and drilling.

20210116_102710-X2.jpg


20210116_102720-X2.jpg



Measured and marked center line of the aluminum tubing them marked where I wanted the bolts to be placed. Using a small pilot bit I drilled through the board and into the aluminum.

20210116_103154-X2.jpg


20210116_103158-X2.jpg


20210116_105347-X2.jpg



Next I up-sized the pilot holes in the frame to 3/8" to fit the TRIC-nuts.

20210116_110312-X2.jpg



And installed and set all the TRIC-nuts in place.

20210116_110312-X2.jpg



Continued Below....

Hodakaguy
 

Hodakaguy

Adventurer
Continued From Above....

Deburring the holes.

20210116_115245-X2.jpg


20210116_110818-X2.jpg


20210116_111419-X2.jpg



Next I drilled out the holes in the boards to 1/4" and counter sunk them for the bolts.

20210116_150723-X2.jpg


20210116_150738-X2.jpg



Test fitting the panel. Fits great!

20210116_112603-X2.jpg


20210116_112653-X2.jpg


20210116_120052-X2.jpg



One panel down.....

20210116_120230-X2.jpg



And the second panel complete.

20210116_150848-X2.jpg



Next up all the wood panels were sanded to 240 grit in preparation for sealing. I'm using OSMO Polyx-Oil (See Below) to seal the boards and you don't want to go any smoother than 240 Grit as you need some grain for the oil to soak into the wood.

20210116_151743-X2.jpg



I'm using OSMO Polyx-oil in Clear Satin to seal the boards. OSMO is great stuff! Human safe and can be applied without making a mess, love the natural finish it provides. Stir the product really well before use and every now and then while you work. To apply the OSMO you use a non abrasive 3M pad and apply a really thin layer of OSMO. Work the oil into the the wood (Can go with or against the grain with the non abrasive pad). Once the wood is fully covered you take a fresh piece of pad and rub it all down again until there are no "wet" spots left and your left with a nice smooth finish. Wait 8-10 hrs and apply a second coat with the same technique and you have a nice sealed finished product.

Note: The links below are my Amazon Affiliate links, I make a small portion each time someone purchases from Amazon using one of my links, at no extra cost to the buyer. I only provide links to items that I personally like and use myself. i use the money to put back into my builds and support making videos/posts. If you prefer not to use my links you can search for the same items directly off Amazon. Thank you for the support!

OSMO Polyx-Oil: Available on Amazon here: https://amzn.to/2XKMgxo
3M White Application Pads: Available on Amazon Here: https://amzn.to/3imLlgj

20210116_161705-X2.jpg


20210116_162919-X2.jpg



Applying the first coat. Love the finish!

20210116_162910-X2.jpg


20210116_164513-X2.jpg


20210116_170049-X2.jpg



Hanging up to dry.

20210116_170146-X2.jpg



All the boards are now complete with the first coat, will apply the second coat in 8-10hrs.

More to come soon....

Hodakaguy
 

Hodakaguy

Adventurer
All together......

Up early the next morning to apply the second coat of OSMO to the boards, then let them dry. Later that afternoon I started the assembly process.

20210117_095557-X2.jpg



I used Loctite 243 on the bolts that thread into the aluminum TRIC-nuts, and Antiseize on the 4 bolts with Nylocks.

20210117_095822-X2.jpg


20210117_095919-X2.jpg


20210117_101114-X2.jpg


20210117_101330-X2.jpg


20210117_101436-X2.jpg


20210117_101502-X2.jpg



One panel assembled.

20210117_101926-X2.jpg


20210117_101949-X2.jpg



Here's a look again at the horizontal mounting rail. This rail can move up and down the vertical L-track to adjust the bed height. The bed itself will expand in and out as the bed goes up and down to accommodate for the walls being closer together as you go up.

20210117_135154-X2.jpg


20210117_135451-X2.jpg



Continued Below......

Hodakaguy
 

Hodakaguy

Adventurer
Continued from above....

And both panels back in the Van. Pretty happy with how they turned out.

20210117_142515-X2.jpg


20210117_142522-X2.jpg


20210117_142529-X2.jpg


20210117_142555-X2.jpg


20210117_142656-X2.jpg


20210117_142700-X2.jpg


20210117_142807-X2.jpg


20210117_142910-X2.jpg


20210117_142921-X2.jpg


And a shot of the Mule overhead storage bags.

20210117_142820-X2.jpg


20210117_142931-X2.jpg


20210117_143050-X2.jpg



Now I'll let the OSMO fully cure for a day or so then throw the mattress back in. Now on to a few other finishing details.

More to come....

Hodakaguy
 
Last edited:

Heifer Boy

Adventurer
Very very nice as always. Your attention to detail is amazing but it certainly produces a quality job.

I may have missed it but how do you actually raise and lower the bed base?

HB

Sent from my XT1635-02 using Tapatalk
 

Hodakaguy

Adventurer
Very very nice as always. Your attention to detail is amazing but it certainly produces a quality job.

I may have missed it but how do you actually raise and lower the bed base?

HB

Sent from my XT1635-02 using Tapatalk


You first push the bed frames together which released them from the horizontal mounting bars. Then remove the two nuts securing the mounting bars to the L-track on each side and raise the bars to the new desired position. Re-tighten the nuts and re-install the frames. Takes maybe 10-15 minutes to change position, not something you usually do while out on the road but I liked having the option.

Hodakaguy
 

Forum statistics

Threads
188,120
Messages
2,902,344
Members
229,523
Latest member
winnrider
Top