Robthebrit
Explorer
Not to hijack the thread but I have a pretty unique perspective on the manual/auto argument as my truck is effectively either. I can driver over an obstical as a stick shift, reverse and drive over it again as at auto!!
A stick will make you a better driver as you have another dimension of the vechicle control to deal with, however this additional level of control can get you in trouble by stalling in a really bad place. On the other hand with an auto its easy to mistake your ability for the capability of the truck as you effortlessly glide over steep obsticals without ever slipping a wheel. To make the required torqure to drive over a steep obstical with a gas engine you typically need high RPMs which and a stick puts you in a situation of high clutch wear and spinning wheels (your transfer case helps with this). In this same scenario the 3:1(maybe more) torque multiplication of the converter and the slippage allows for a lower engine RPM and no wheel slip. An automatic while driving offroad can easily get the tranny temperature light to come on as all that torque converter slippage generates a lot of heat, if you do a lot of driving on anything other than dirt roads you might want a tranny cooler and change your fluid more often. A stick in an diesel is a completely different beast and much easier to deal with.
Going downhill, the stick has an advantage, engine breaking is significantly reduced with a torque converter and in a small truck may not be effective at all. To get any engine breaking you typically have to shift to a lower gear which is a problem if you are already in the lowest gear. For me this is not a problem as A) I always have a lower gear B) I get pretty good engine breaking to start with as my torque converter is nearly 2 feet across C) I have an exhaust break and D) my converter locks up at 1600rpm so if I change to a low enough gear and get over 1600 rpms I get full engine breaking.
Not being able to handle a stick off road has the potential to damage the engine, for example accidently rolling back on a steep hill while in a too high forward gear and letting the clutch out, or you are already stalled, you start to roll back and you let the clutch out. Regardless of the setup you are trying to turn the engine over backwards and a lot of modern engines (and some old over head cam engines) will slip the timing and you'll be really stuck.
The mechanical reliability of a modern automatic is greater than a stick especially as the clutch in the stick shift ages. However, if a modern auto does break or goes into limp mode then you'll have problems getting it fixed in the middle of nowhere and you'll be driving home in 2nd gear! If you drive a stick to the middle of nowhere learn how to drive without the clutch just in case you need to.
Just my 2c, now back to the thread.
Rob
A stick will make you a better driver as you have another dimension of the vechicle control to deal with, however this additional level of control can get you in trouble by stalling in a really bad place. On the other hand with an auto its easy to mistake your ability for the capability of the truck as you effortlessly glide over steep obsticals without ever slipping a wheel. To make the required torqure to drive over a steep obstical with a gas engine you typically need high RPMs which and a stick puts you in a situation of high clutch wear and spinning wheels (your transfer case helps with this). In this same scenario the 3:1(maybe more) torque multiplication of the converter and the slippage allows for a lower engine RPM and no wheel slip. An automatic while driving offroad can easily get the tranny temperature light to come on as all that torque converter slippage generates a lot of heat, if you do a lot of driving on anything other than dirt roads you might want a tranny cooler and change your fluid more often. A stick in an diesel is a completely different beast and much easier to deal with.
Going downhill, the stick has an advantage, engine breaking is significantly reduced with a torque converter and in a small truck may not be effective at all. To get any engine breaking you typically have to shift to a lower gear which is a problem if you are already in the lowest gear. For me this is not a problem as A) I always have a lower gear B) I get pretty good engine breaking to start with as my torque converter is nearly 2 feet across C) I have an exhaust break and D) my converter locks up at 1600rpm so if I change to a low enough gear and get over 1600 rpms I get full engine breaking.
Not being able to handle a stick off road has the potential to damage the engine, for example accidently rolling back on a steep hill while in a too high forward gear and letting the clutch out, or you are already stalled, you start to roll back and you let the clutch out. Regardless of the setup you are trying to turn the engine over backwards and a lot of modern engines (and some old over head cam engines) will slip the timing and you'll be really stuck.
The mechanical reliability of a modern automatic is greater than a stick especially as the clutch in the stick shift ages. However, if a modern auto does break or goes into limp mode then you'll have problems getting it fixed in the middle of nowhere and you'll be driving home in 2nd gear! If you drive a stick to the middle of nowhere learn how to drive without the clutch just in case you need to.
Just my 2c, now back to the thread.
Rob