Hodakaguy's 4x4 Sprinter Build

[Hodakaguy]

Continued from above...

Next we left Wallace and headed about 7 miles out of town to the ghost town of Burke ID. Burke was one of the largest producers of silver, zinc and lead. Look up Burke on youtube for some really cool history.

Burke back in the day.....

Today little is left except small ruins, you would never know how massive this place really was.

Massive head frame in the background.

What's left of the Frisco Mill. During a battle between the miners and the mill owners the miners placed explosives in a mine cart above the mill and sent the cart down the tracks into the mill, completely destroying the mill.

Shot from the Drone

Stopped at the 50,000 silver dollar store in Montana. Just cheap tourist stuff here but kinda cool to check out.

Using the Biolite grill to cook up some steaks for dinner...yummm

My wife enjoying the trip....

Continued Below....

 

[Hodakaguy]

Continued from above...

Dad setting up camp...takes all of about 2 minutes. The Vagabond Drifter is a slick setup!

Next we stopped in Missoula MT....Ehh...just a big city and we weren't to impressed so didn't spend much time here.

Back on the road and heading south towards the Salmon river. Several cool towns to stop and explore along the way.

Stickers on entering state signs must be a thing now

Lots of beautiful scenery along the way.

Found a great free camp site right on the Salmon river...soooo nice! While we were camped here a park ranger stopped by to chat and we told him that we were heading to the Yankee Fork gold dredge and the ghost town of Custer ID. He told us that there is a historic dirt road called the Custer Motorway that would take us right to Custer and avoid paved roads, heads up over the mountains at 9k feet.... just turn at Challis and follow the dirt road. Awesome! Custer Motorway it will be!

Kiddo got a lot of play time in the river

Camp from above

Doesn't get much better than this!

Continued Below...

 

[Hodakaguy]

Continued from above...

If anyone has ever watched Lucy and the long long trailer you will get this...my wife started collecting rocks to bring home lol.

Heading out again....more amazing scenery

Heading up into the mountains on the Custer Motorway.

Time to get the drone out again for another perspective.

Continuing down the trail.

Kiddo cruising on the bed

More history. This was once a toll road and whats left of the toll cabins are still here at 9k feet. Very cool!

Wild strawberries...yummmm

Continued below...

 

[Hodakaguy]

Continued from above...

Didn't take long to find the old dump site.

A little photography along the way

Next we visited the ghost town of Custer. Another great piece of history. But first up...breakfast

In a small remote ghost town in the mountains of ID we ran into Chad with Adventure Wagon! Chad is an awesome guy and makes some really cool Sprinter gear. We are running his Mule bags and basically patterned a lot of our interior off his kits. Great to chat with you Chad!

Showing Chad our build.

Chad even placed a Hodakaguy sticker on his van

Custer from the Air

And checking out the old buildings.

Next we explored the abandoned Yankee Fork gold dredge. Unlike the Sumpter dredge that we explored last trip the Yankee dredge is completely intact with all the original equipment...plus they let you climb and explore on all levels!! Such a cool piece of mining history.

Heading into the dredge, people provide a good reference and show the scale of the bucket line.

I spy a Sprinter

Continued Below....

 

[Hodakaguy]

Continued from above...

Massive electric powered winches. These were used to position the dredge and raise/lower the bucket line.

Resistor banks used as speed controls for the motors

Thats it...just a little further

Upper axle on the bucket line

Grizzly bars to reject large rocks before they get to the trommel.

Bull gear that drives the bucket line. This is the weakest spot on the dredge, the large bull gear was replaced 3 times while this dredge was in operation.

Trommel from above

Checking out the sluice runs

Gold recovery area, the pot on the lower right was used to burn off the mercury and recover the gold.

The dredge made its own power via two 1940 Ingersol Rand Diesel engines running two generators.

Got the drone back out for a few shots of the dredge

Great shot of the tailings left behind from the dredge

Continued Below...

 

[Hodakaguy]

Continued from above...

Wife got in a little panning while we were there...didn't get anything but more cool rocks to pack in the van

Sawtooth Mountains as we head south and home

Hot springs along the hwy....gonna have to come back here!

Restaurant along the road lol.

Stopped for ice cream and had to leave a sticker

Next morning all that was left was to make coffee and roll into home.

Hodakaguy

 

[Hodakaguy]

Back to the Build out....

On the last trip we liked the Mule bags so well that we ordered a third bag while we were on the road. These bags are very well thought out and really help organize the van and keep clutter off the floor. Here I'm getting ready to install the two missing panels and install the 3rd Mule bag.

Sealing the screw hole with a soldering iron to ensure the tweed can't start fraying.

Panels installed

Mule bag out of the box.

Installing the mounting hardware onto the L-track.

And installed. Lots-0-Storage space

The crank for the Fiamma awning fits perfectly in the loops on the bottom of the bag.

Continued below...

 

[Hodakaguy]

Continued from above...

Next up it's time to seal this van up and make it weather proof. There is a glaring over site on Mercedes part when they designed the clips for the plastic side panels. Water can easily run behind the clips and into the walls during rain storms or when washing the van....not good. Now that I have my walls insulated the last thing I want is water getting trapped in with the insulation, time to fix this issue.

THIS IS A MUST DO FOR ANY SPRINTER

Note: For 2019 Mercedes finally decided to address this issue by adding a little rubber lip around each retaining clip to keep water out. I've heard that the seal is marginal at best and it's recommended that you still remove & seal these clips as well for a reliable waterproof seal.

Time to start removing the trim

The rear edges of the front doors and both ends of the slider doors have screws that need to be removed.

I purchased a cheap set of plastic body panel removal tools from Harbor Freight to remove the trim panels, they worked great. Note: Make sure the fulcrum of the tool is below the edge of the body panel so you don't leave any small dimple dents as you remove the panels. While pulling on the panel from the end work the tool down the trim piece and pop loose each trim clip.

Some clips will stay with the trim piece and some will stay in the body....either way not a big deal.

Next I removed the clips from the body using another one of the HF tools. You can use a screw driver here as well to reach in and compress/release each side of the clips, the HF tool makes it a quick process. The only thing keeping water out is the plastic contact against the body, and it's not a very good seal. Go slow and you won't break and of the clips, I managed to remove all the clips without breaking any in the process.

Next I used a bent pair of needle nose pliers to release the clips that were still attached to the side panels. I just reached in with the pliers and slightly compressed the tabs until the clip released.

Clips and Panels Removed.

Continued Below...

 

[Hodakaguy]

Continued from above...

I first cleaned the body surfaces a couple times with Windex then went over the clip locations with some wax/de-greaser.

HodakaDad helping me clean the clips

I'll be using Sikaflex 221 to seal the clips to the body.

Sika applied to the clips

The clip is installed vertically, I installed them slightly off vertical then rotated them into position for a good seal.

With all the clips sealed in place just line up the panels to the tabs and use your palm to snap the panels back into place. Nice and waterproof now, I'll sleep easier when it rains now

Next up I started the install of the Switch Pro SP9100. The Switch Pro is a programmable 8 position switch panel that you can use to control your accessories (Lights, Air compressors, etc). The unit is fully programmable with the phone app...you can tie switches together, make a switch start stop with the engine, tie aux lights to your high beams etc. I had one on my last build and loved it, very versatile and a super clean way to add a bunch of switches. The head unit/switch assembly is very thin and robust, the brains of the unit is all solid state and has it's own over current protection. The unit comes with stickers that you place on each switch location to mark your intended use for that switch, the lighting is dim-able and you can change it to any color.

The switch panel.

I decided to place the unit in the headliner above the dome light assembly. It's within easy reach here and I don't have to look at the lighting while driving at night.

Marking out the hole location.

Continued Below....

 

[Hodakaguy]

Continued from above...

Used a razor knife to cut the tweed.

Then used a soldering iron to burn the edges of the tweed to keep the fabric from fraying.

Next up I used an ultrasonic tool to cut out the headliner

Preparing the switch unit for install by inserting the studs on the rear of the unit that hold the retaining clips in place

Switch unit installed.

The brains of the unit will be installed soon.

More to come soon....

Hodakaguy

 

[jgaz]

Continued from above...

Wife got in a little panning while we were there...didn't get anything but more cool rocks to pack in the van

Sawtooth Mountains as we head south and home

Hot springs along the hwy....gonna have to come back here!

Restaurant along the road lol.

Stopped for ice cream and had to leave a sticker

Next morning all that was left was to make coffee and roll into home.

Hodakaguy

Excellent pics and trip report.
Thanks for posting them.

And thanks for the tip on sealing the trim clips. Passing it on to a Sprinter driving friend.
You‘re right, it is a poor design.

 

[ericvs]

I am dreading doing the plastic on my van, but your post was inspiring!
Thank you.

Great build, looking forward to following along

 

[Arjan]

Love the trip report - thank you VERY much !

That build is very inspiring.

Looking at an Inveco 4x4 Daily here in France...

 

[MCX]

Loved the pictures...beautiful country! That dredge looks like it could be started up tomorrow and start dredging for gold.

 

[Hodakaguy]

I am dreading doing the plastic on my van, but your post was inspiring!
Thank you.

Great build, looking forward to following along

It really isn't a bad job, just take it slow and it goes nice and smooth.

Hodakaguy